Votos - 3, Puntuación media: 3.7 ( )

Fabricar: MTD Tamaño del archivo: 8.57 mb Nombre del archivo: Idioma del manual:

DO NOT twist key after it is inserted. 7. If engine is cold, apply choke. A warm engine requires less choking than a cold engine. See Engine Manual for detailed instructions. 8. Set throttle to proper starting position. 9. Press starter button on engine until engine starts. IMPORTANT: DO NOT operate starter more than 15 seconds per minute, as overheating and damage can occur. (If engine does not start, refer to TROUBLESHOOTING on page 36.) 10. Adjust choke as needed. 11. Disconnect power cord from outlet, then starter. 12. Set throttle to Part Throttle or Slow position for adaptation to outside temperature or travel. Set throttle to Fast position for normal operation. Shut Off 1. Release Traction Drive Clutch Lever and allow unit to come to a complete stop. 2. Run Impeller a few minutes after use to prevent freeze-up of Impeller. 3. Release Attachment Clutch Lever and wait for all moving parts to come to a complete stop. 4. Move Throttle to the “Stop” position. 5. Remove key. Snow Removal IMPORTANT: Allow unit and engine to adjust to the outdoor temperature before clearing snow. NOTE: Attachment clutch should be engaged before wheel drive clutch when throwing snow. 1. Select Speed Control position and direction. 2. Engage Attachment Clutch - Right Hand Lever. 3. Engage Traction Drive Clutch - Left Hand Lever. IMPORTANT: DO NOT overload unit capacity by attempting to clear snow at too fast a rate. Use slow speed to clear deep or hard packed snow. Tips for Operation Snow is best removed as soon as possible after snow fall. To clear an area, run unit in an overlapping series of paths. For large areas, start in the middle and throw snow to each side, so snow is not cleared more than once. ALWAYS direct snow away from area to be cleared and with direction of the wind. Traveling To travel from one work area to another: 1. Set Throttle to Slow or Part-Throttle position. 2. Press down on handlebars enough to raise front of unit slightly off surface. 3. Engage wheel drive clutch without engaging attachment drive clutch. Transport ALWAYS shut off engine, remove key, and close fuel shut-off valve when transporting unit on a truck or trailer. Use extra care when loading or unloading unit onto trailer or truck. Secure unit chassis to transport vehicle. NEVER secure from rods or linkages that could be damaged. DO NOT transport machine while engine is running. GB - 20 MAINTENANCE Ariens Dealers will provide any service or adjustments which may be required to keep your unit operating at peak efficiency. Should engine service be required, contact an Ariens dealer or an authorized engine manufacturer's service center. ▲ WARNING: AVOID INJURY. Read and understand the entire Safety section before proceeding. Service Position ▲ WARNING: Before tipping unit up onto housing, remove fuel so no spills will occur. Ensure unit is secure and will not tip over during maintenance. Place unit on a flat level surface. Tip unit forward onto front of auger housing for service. Ensure unit is secure and will not tip over. Strap and clamp onto bench if needed. The chart below shows the recommended maintenance schedule that should be performed on a regular basis. More frequent service may be required. MAINTENANCE SCHEDULE Service Performed Each Use Every 5 hrs. Every 25 hrs. Yearly Check Dual Handle Interlock Check Fasteners • Check Clutch Operation • Check Clutch Spring Adjustments * Clean Engine • Check Engine Oil • • Change Engine Oil ** ** • Check Tire Pressure • Check Auger Gearcase • • General Lubrication • • After first five hours of operation. After first two hours of operation, thereafter every 25 hours. Check Dual Handle Interlock Without the engine running, press down (engage) both clutch levers. Release attachment clutch lever. Attachment clutch should remain engaged until traction clutch lever is released, then both clutches must disengage. Check Fasteners Make sure all hardware is tightened properly. Check Clutch Operation Auger / impeller must stop within 5 seconds when attachment clutch/impeller brake lever is released. Wheels must stop quickly when traction drive clutch lever is released. GB - 21 If clutches do not engage or disengage properly, adjust or repair before operation. See Attachment Clutch/Brake Adjustment on page 27 and Traction Drive Clutch Adjustment on page 30. Clean Engine Refer to Engine Manual for detailed instructions. Check engine oil The engine crankcase oil should be checked every 5 hours of operation. Oil level MUST be maintained in safe operating range on dipstick at all times or engine damage will result (See Engine Manual). Park unit on a level surface. Refer to Engine Manual for detailed instructions. Change Engine Oil Change oil after first 2 hours of operation, thereafter change oil every 25 hours (more often if required). Refer to Engine Manual for detailed instructions. Run engine just prior to ...

Descargar ahora

Introduzca dos números de la imagen: