Votos - 3, Puntuación media: 3.7
(
)
)
|
Resumen del manual
• Remove the two clevis pins which fasten the blade's hanger brackets to the tractor's mower deck suspension brackets (or frame brackets). See figure 11 on page 10. • Remove the clevis pin that fastens the blade's rear mounting bracket to the tractor's drawbar and drop the rear of the blade frame to the ground. See figure 10 on page 10. • Remove the frame brackets (if used). See figure 3 on page 6. • Back the tractor off of the blade assembly. TROUBLESHOOTING CAUSE Lift mechanism is binding Handle tube is binding on lift rod. Lock mechanism is out of adjustmentLock mechanism is out of adjustment and is not disengaging. PROBLEM Blade is difficult to raise. Blade is difficult to pivot. Blade will not unlock to pivot. CORRECTION Lubricate pivot points as shown in figure 27 on page 15. Lubricate lift handle rod as instructed in figure 27 on page 15. Refer to the Service and AdjustmentsRefer to the Service and Adjustments section on this page. 16 NOTES 17 18 PARTS 44 6 59 28 48 59 52 61 29 55 58 51 61 55 58 B B A A 3 8 8 10 30 35 35 50 33 34 45 38 23 46 32 42 56 15 14 19 39 40 24 27 20 48 48 37 47 41 41 25 36 25 25 41 41 11 36 21 21 17 13 6 47 43 12 26 4 5 4 4 7 7 6 6 6 6 47 31 55 36 25 C C 57 54 2 1 22 49 52 52 38 D D 51 58 52 60 53 51 52 52 18 16 16 52 51 51 51 51 51 9 52 52 52 63 62 64 65 REPAIR PARTS LIST FOR MODEL 486.244283 - 48" SNOW BLADE REPAIR PARTS LIST FOR MODEL 486.244283 - 48" SNOW BLADE 1 23955 1 Blade 48" 2 23956 1 Wear Plate 48" 3 62980 1 Reinforcement Plate Assembly4 43080 6 Bolt, Carriage 5/16-18 x 3/4" 44326 4 Bolt, Carriage 5/16-18 x 1" 6 47810 15 Nylon Lock Nut, 5/16-18 Thread7 43081 4 Washer, 5/16" 8 24690 2 Skid Shoe9 64732 1 Thrust Channel24347 1 Push Channel11 43262 1 Hex Lock Nut, 1/2-13 Thread12 23131 1 Bolt, Special Pivot13 1540-118 1 Washer, Flat 1/2" 14 23958 1 Plate, Pivot 7 Ga. 23130 1 Bracket, Spring Mt. 16 24659 2 Rear Support Channel17 46066 1 Shaft, Blade Pivot18 25125 1 Rear Mounting Bracket 19 R9466R 1 Spring, Blade Adjust44071 1 Hex Bolt, 3/8-16 x 3-1/2" 21 43015 2 Hex Nut, 3/8-16 Thread22 44074 1 Plastic Cap23 746-0366 1 Control Cable Assembly24 62561 1 Release Grip Assembly43055 4 Pin, Hairpin Small 3/32" 26 46053 2 Spacer, .28 ID x 1" 27 63033 1 Lift Handle Rod Assembly28 25121 1 Short Hanger Bracket29 25122 1 Long Hanger Bracket24023 1 Pivot Support Bracket31 46049 1 Rod, Blade Pivot32 62972 1 Lift Handle Tube Assembly33 23151 2 Angle Lock Bar34 23856 1 Spring Mount Rod35 44917 2 Palnut, 3/8" 36 43010 3 Cotter Pin 1/8" x 1-1/4" 37 43348 1 Angle Lock Spring38 746-0260 2 Cable End Fitting39 731-0869 1 Grip, Plastic40 46471 1 Handle, Grip 41 712-0256 4 Hex Jam Nut, 5/16-24 Thread42 23658 1 Spacer43 43085 1 Hex Bolt, 5/16-18 x 1-1/2" 44 43063 4 Bolt, Hex 5/16-18 x 1" Lg. 45 05762 1 Cable Mount Bracket46 1509-90 1 Hex Bolt 1/4-20 x 1-1/4" 47 47189 3 Nylon Lock Nut, 1/4-20 Thread48 710-0305 4 Carriage Bolt, 3/8-16 x 1-1/4" 49 46065 1 Channel Pivot Pin50 63034 1 Lift Link Assembly51 43350 18 Carriage Bolt, 3/8-16 x 1" 52 HA21362 22 Nylon Lock Nut, 3/8-16 Thread53 HA23380 1 Rear Locating Bracket54 726-0178 2 Plastic Tie55 R191716163 Washer56 46071 1 Hex Bolt, 1/4-20 x 3-1/4" Lg. Gr 57 43349 1 1/4" x 1" Spring Pin58 43343 3 Pin, 3/32" Hairpin (Large) 59 44062 2 Clevis Pin, 1/2" x 1" Lg. 60 HA3980 1 Clevis Pin, 5/8" x 1-3/4" Lg. 61 25124 2 Frame Bracket62 43003 2 Lock Washer, 3/8" 63 43001 2 Hex Bolt, 3/8-16 x 1" 64 R747808281 Hex Bolt, 1/2-13 x 1-3/4" 65 712-3083 1 Nylon Lock Nut, 1/2-13 Thread49828 1 Owners Manual34 23856 1 Spring Mount Rod35 44917 2 Palnut, 3/8" 36 43010 3 Cotter Pin 1/8" x 1-1/4" 37 43348 1 Angle Lock Spring38 746-0260 2 Cable End Fitting39 731-0869 1 Grip, Plastic40 46471 1 Handle, Grip 41 712-0256 4 Hex Jam Nut, 5/16-24 Thread42 23658 1 Spacer43 43085 1 Hex Bolt, 5/16-18 x 1-1/2" 44 43063 4 Bolt, Hex 5/16-18 x 1" Lg. 45 05762 1 Cable Mount Bracket46 1509-90 1 Hex Bolt 1/4-20 x 1-1/4" 47 47189 3 Nylon Lock Nut, 1/4-20 Thread48 710-0305 4 Carriage Bolt, 3/8-16 x 1-1/4" 49 46065 1 Channel Pivot Pin50 63034 1 Lift Link Assembly51 43350 18 Carriage Bolt, 3/8-16 x 1" 52 HA21362 22 Nylon Lock Nut, 3/8-16 Thread53 HA23380 1 Rear Locating Bracket54 726-0178 2 Plastic Tie55 R1917161656 46071 1 Hex Bolt, 1/4-20 x 3-1/4" Lg. Gr 57 43349 1 1/4" x 1" Spring Pin58 43343 3 Pin, 3/32" Hairpin (Large) 59 44062 2 Clevis Pin, 1/2" x 1" Lg. 60 HA3980 1 Clevis Pin, 5/8" x 1-3/4" Lg. 61 25124 2 Frame Bracket1 23955 1 Blade 48" 2 23956 1 Wear Plate 48" 3 62980 1 Reinforcement Plate Assembly4 43080 6 Bolt, Carriage 5/16-18 x 3/4" 44326 4 Bolt, Carriage 5/16-18 x 1" 6 47810 15 Nylon Lock Nut, 5/16-18 Thread7 43081 4 Washer, 5/16" 8 24690 2 Skid Shoe9 64732 1 Thrust Channel24347 1 Push Channel11 43262 1 Hex Lock Nut, 1/2-13 Thread12 23131 1 Bolt, Special Pivot13 1540-118 1 Washer, Flat 1/2" 14 23958 1 Plate, Pivot 7 Ga. 23130 1 Bracket, Spring Mt. 16 24659 2 Rear Support Channel17 46066 1 Shaft, Blade Pivot18 25125 1 Rear Mounting Bracket 19 R9466R 1 Spring, Blade Adjust44071 1 Hex ...