Votos - 2, Puntuación media: 3
(
)
)
|
Resumen del manual
Do not attempt to clear steep slopes. Refer to the slope guide on page 19 of this manual. • Never operate the snow thrower without guards, plates or other safety protection devices in place. • Never operate the snow thrower near glass enclosures, automobiles, window wells, drop offs etc. without proper adjustment of the snow-thrower discharge angle. • Never direct discharge at bystanders or allow anyone in front of the snow thrower. • Never run the snow thrower into material at high speeds. • Do not overload the machine capacity by attempting to ctear snow at too fast a rate. • Never operate the machine at high trar_sport speed on slippery surfaces. Look behind and .use care when backing. • Watch for traffic and stay alert when crossing or operating near roadways. • Disengage power to the snow thrower when transporting or when not in use. • Use only attachments and accessories approved by the manufacturer of the snow thrower (such as wheel weights, counter weights, cabs etc.) • Never operate the snow thrower without good visibility or light. ,_ Look for this symbol to point out important safety precautions. It mean--Attention!! Become alert!! Your safety is involved. SHOWN ACTUAL SIZE Two shear bolts (X) and hex lock nuts (Y) are provided as replacement parts for the spiral augers. Store in a safe place until needed. (See page 17,) U IW I I NOT SHOWN ACTUAL SIZE /Z cc cc /GG REF. QTY. DESCRIPTION REF. QTY. DESCRIPTION A 1 Hex Bolt, 1/2" x 1-1/4" Q 6 Hex Lock Nut, 1/4" B C 4 2 Hex Bolt, 3/8" x 1" Hex Bolt, 5/16" x 1-3/4" R S 12 9 Hex Nut, 5/16" Hex Lock Nut, 3/8" -D 6 Hex Bolt, 1/4" x 1" T 1 Hex Nut, 1/2" E 2 Slotted Truss Head Bolt, 3/8" x 1" U 2 Hairpin Cotter, 5/64" F 4 Carriage Bolt, 3/8" x 1" • V 1 Hairpin Cotter, 3/32" G H 2 2 Carriage Carriage Bolt, 5/16" x 1-3/4" Bolt, 5/16" x 1-1/4" W X 4 2 Hairpin Cotter, Shear Bolt 1/8" I 6 Carriage Bolt, 5/16" x 1" Y 2 Hex Lock Nut, 5/16" J 4 Shoulder Bolt, 3/8" x 5/8" Z 1 Tarp Strap K 12 Lock Washer, 5/16". AA 1 Spring L 10 Lock Washer, 3/8" BB 3 Chute Keeper M 1 Lock Washer, 1/2" CC 1 Chain, Tensioning N 6 Washer, 1/4" DD 1 Trunnion O P 2 2 Washer, 5/16" Bowed Washer EE FF 1 2 Plastic Cap Lock Pin GG 1 Nylon Tie CARTON CONTENTS 1. Cross Brace (Weight Tray) 2. Side Brace (Weight Tray) 3. Right Hand Side Plate (Stamped 4. Left Hand Side Plate (Stamped 5. Anti-rotation Bracket 6. Engagement.Rod 7. Engine Pulley Keeper 8. Chute Crank Rod Assembly 9. Support Tube, Crank Rod 10. Plastic Keg 14 "R';) "L") 14. Clutch 15. V Belt, 16. V Belt, 17. Chute 18. Weight 11. Left Hand Hanger Bracket (Stamped "L") 12. Right Hand Hanger Bracket (Stamped "R") 13. Lift Handle Tube and Cable Idler Assembly 55" 112" (Attached to Housing Assembly) and Control Cable Assembly Tray 19. Housing Assembly Hardware Package (Stored inside Plastic Keg) 11 12 18 17 19 TOOLS REQUIRED FOR ASSEMBLY (2) 7/16" Wrenches (2) 1/2" Wrenches (2) 9/16" Wrenches (2) 3/4" Wrenches (1) Knife ADDITIONAL ITEMS REQUIRED General Purpose Grease REMOVAL OF PARTS FROM CARTON Remove all parts and hardware packages from the carton. Lay out all parts and hardware and identify using the illustrations on pages 4 and 5. NOTE: Not all of the supplied parts and hardware will be used. If your tractor has a manual attachment clutch, you will not use items S(1), V(1), AA(1) and CC(1) shown on page 4. If your tractor has an electric attachment clutch, you will not use Items U(2) and DD(1) shown on page 4, and items 6 and 7 shown on page 5. & & CAUTION: Before starting to assemble the snow thrower, remove the spark plug wire(s), set the parking brake and remove the key from the tractor ignition, TRACTOR PREPARATION Before proceeding with these instructions, refer to the Service and Adjustments section of your tractor owner's manual for specific safety Instructions. • Allow engine, muffler and exhaust deflector to cool before beginning. • Remove any front or rear attachment which is mounted to your tractor. • -Remove the mower deck. Refer to your tractor owner's manual for removal instructions. Mark all loose parts and save for re-assembly. • Remove the tractor hood and grill assembly. Refer to your tractor owner's manual for removal instructions, ASSEMBLY OF PARTS TO TRACTOR FRAME Right hand (R.H.) and left hand (L.H.) are determined fTOmthe operators positionwhile seated on the tractor. • Remove and save two bolts from each side of the tractor frame as shown in figure 1. BOLTS REMOVEDFROM THESEHOLES FIGURE 1 Assemble the R.H, Side Plate (marked with an "R") to the now empty holes In the right hand side of the tractor frame using two 3/8" x 1" hex bolts and 3/8" lock washers as shown In figure 2. Repeat for the L,H, side. NOTE: If the side plates are removed from the tractor frame, bolts must be assembled back into the empty holes in the frame. 3/8" LOCK WASHER 3/8" X 1" HEX BOLT FIGURE2 6 • Assemble a shoulder bolt to the bottom hole in each side plate, securing each bolt with a 3/8" lock washer and a 3/8" hex lock nut. See fig...