Votos - 3, Puntuación media: 3.7
(
)
)
|
Resumen del manual
See figure 18. CHUTE CRANK ROD CRANK SUPPORT TUBE TILT CONTROL HANDLE TILT 5/16" x 1-3/4" CONTROL CARRIAGE BOLT ASSEMBLY BOWED WASHER 5/16" LOCKWASHER _16"HEX NUT FIGURE 18 LEFT SIDE VIEW Attach the chute crank rod assembly brackets to the plastic bracket on the left side of the thrower housing. Align the chute crank bracket beneath the rod support bracket and assemble both to the plastic bracket using two 5/16" x 1" carriage bolts, 5/1 6" flat washers, 5/1 6" lock washers and 5/1 6" hex nuts. Do not tighten yet. See figure 19. lO 5/16" x 1" \\ \ CHUTE CRANK BRACKET .,dw,,,.,,,,. _CARRIAGEBOLT CHUTE CRANK ROD ROD SUPPORT J BRACKET / _16"FLAT WASHER WASHER 5/16"LOCK _ "5/16"HEX NUT FIGURE 19 LEFT SIDE VIEW Coat the top of the ring around the discharge opening with general purpose grease. See figure 20. • Place the discharge chute (facing forward) onto the ring. Place the anti-rotation bracket on top of the chute flange, aligning it with the holes on the right hand side of the flange. Attach the three chute keepers (right side up as shown) to the bottom of the flange using six 1/4" x 1" hex bolts, 1/4" flat washers and 1/4" flanged lock nuts. Tighten carefully so that the nuts are snug but do not dig into the plastic chute keepers. See figure 20. • Place the plastic cap onto the short end of the anti- rotation bracket. See figure 20. • Position the crank rod spiral so that it does not rub against the bottoms of the notches in the chute flange. Tighten the nuts. Refer back to figure 19. • Check if the crank rod rotates the chute freely. If not, loosen by 1/4 turn each of the six hex bolts holding the chute keepers to the chute flange. • Secure the control cables to the crank rod support tube using a nylon tie. 1/4" x 1" ANTI-ROTATION BRACKET I_"FLAT WASHER FLANGE PLASTIC CAP GREASED SURFACE CHUTE KEEPER 1/4" FLANGED LOCK Nu'r ATTACHING SNOW THROWER TO TRACTOR NOTE: An additional person's help may be required to mount the snow thrower to the front of the tractor. • Place the tractor and snow thrower on a flat, level surface so that the tractor can be rolled forward to attach the snow blower. • Remove the Attachment Pin from the snow thrower. Extend the belt out behind the snow thrower, making sure the belt is still looped over the top of the large drive pulley and underneath the two idler pulleys. The "V" side of the belt must be seated in the grooves of all three pulleys. • Roll the tractor up behind the snow thrower, centering it between the snow thrower's mounting plates. Raise the rear of the snow thrower by lifting up on the lift handle until the notches in the mounting plates align with the shoulder bolts in the tractor's side plates. Guide the bolts into the notches. To ease the assembly of the auger drive belt, delay the installation of the attachment pin shown in figure 21 until you have assembled the belt as instructed for figures 22 and 23. ATTACHMENTPIN 1/8"HAIRPIN COTTER SHOULDER _ BOLT MOUNTING PLATE SIDE PLATE FIGURE 21 RIGHT SIDE VIEW FIGURE 20 RIGHT SIDE VIEW 11 INSTALLINGTHE AUGER BELT INSTALLING THE ATTACHMENT PIN • The auger belt comes preassembled to the pulleys on the snow thrower housing. Make sure the belt Lift the front of the snow blower to align the holes passes over the top of the auger pulley and then in the mounting plates and the side plates. From twists 1/4 turn to pass underneath each side idler the left side of the tractor install the attachment pin pulley. The "V" side of the belt must mate with the through the holes, securing it with the 1/8" hairpin grooves of the pulleys. See figure 22. cotter. Refer back to figure 21 on page 11. AUGER PULLEY TWIST 1/4 TURN 1_ TURN TWIST IDLER IDLER PULLEY PULLEY FIGURE 22 • Push the lift handle down to increase slack in the belt (attachment pin must first be removed). • Remove the 1/8" hairpin cotter that secures the end of the idler arm spring to the right side of the clutch idler assembly. Swing the idler arm to the left side. See figure 23. • Place the auger belt around the rear pulley and between the two pulleys on the idler arm. The "V" side of the belt must be seated in the grooves of the "V" pulleys. See figure 23. Hold this drawing above you while viewing the Clutch/Idler Assembly from underneath the tractor. Right and left in the drawing will be the reverse of the viewer's right and left. 1/8" HAIRPIN COTTER (Removed fromFI IDLER end of spring) ARM REAR LEFT SIDE PULLEY OF TRACTOR SETTING THE AUGER BELT TENSION Pull the tensioning chain until the end of the spring is pulled through the hole in the side of the Clutch/ Idler assembly. Install the 1/8" hairpin cotter through the end of the spring, securing it on the outside of the Clutch/Idler assembly. See figure 24. IMPORTANT: For correct belt tension, the 1/8" hairpin cotter must attach to the end of the spring, not to the chain. Hold this drawing above you while viewing the Clutch/Idler Assembly from underneath the tractor. Right and left in the drawing will be the reverse of the...