Votos - 5, Puntuación media: 4.4
(
)
)
|
Resumen del manual
An adjustable wrench and a 9/16" wrench is required. See figure 7. Tighten securely. 9 1G" WRENCH FIGURE 7 6 REAR SUPPORT ANGLE L.H. FIGURE 8 6. Preassemble the front support channel and the rear support angles as follows: A. Place the front support channel on a work bench or the floor. Place the rear support angles in position as shown in figure 8. B. Place the attaching plates between front support channel and rear support angles. See figure 8. C. Place hex bolts (G) through holes in side of rear support angles, attaching plates and front support channel. See figure 8. D. Secure hex bolts (G) with lock washers (H) hex nuts (I). Make only finger tight. See figure 8. FRONT SUPPORT CHANNEL E. F. Raise front support channel up and secure the bottom four holes with hex bolts (G), lock washer (H) and hex nuts (I). See figure9. Tighten all ten bolts and nuts with 9/16" wrench and adjustable wrench. FIGURE 9 Assemble the front support channel to the snow thrower housing. Place the front support channel between weld plates on housing. On one side, place spacers (S) between channel and housing and secure with hex bolts (R), lock washers (T) and hex lock nuts (W). See figure 10. Just start nuts on by hand. Using a drift pin or punch on by hand. Using a drift pin or punch on the other side, line up spacers (S) between channel and housing and secure in sarre manner. An adjustable wrench and a 3/4" wrench is required.Tighten securely. FIGURE 10 7 8. Assemble the front hanger links (AK) to the front support channel. Insert shoulder bolt (AB) through large hole on hanger links (AK), then through the front support channel. Secure with lock washer (AC) and hex nut (AD). See figure 11. Insert clevis pin (F) through small hole in front hanger links (AK) to hold them in position. Secure with cotter pin (E). See figure 11. Cotter pin and clevis pin will be removed later. NOTE Be sure hanger brackets swing freely on shoulder bolt. 9. Secure right hand drive mounting bracket to rear support angles with hex bolts (AE), lock washers (AF) and hex nuts (AG). See figure 12. Tighten securely. 10. Attach rear hanger brackets to rear support brackets using hex bolts (AH), lock washers (Al) “ and hex nuts (AJ). See figure 13. Tighten finger tight only at this time. note Belt must be assembled as shown in figure 17. Top of belt goes over drive pulley and under idler pulley then twist belt to the left. The bottom of the belt goes to the right. If the belt is assembled incorrectly, the spirals will run in reverse. ATTACHING SNOW THROWER TO TRACTOR NOTE Universal drive shaft is not included with snow thrower attachment. It is included with the cutting deck. If you do not have a cutting deck, order part number 717-0135. 1. Slip female end of drive shaft over shaft of right angle drive. Make sure key way is in shaft. Tighten set screw with 3/8" open end wrench. See figure 18. 2. Slip male end of drive shaft over tractor P.T.O. There are two set screws. Tighten both with 3/8" _ open end wrench. See figure 19. Tractor was elevated for photo clarity. Tractor does not have to be raised to install drive shaft. r~ FIGURE 19 10 FIGURE 20 3. Raise the tractor undercarriage to highest position. 4. Roll the tractor over the rear of snow thrower. 5. Slip the universal drive shaft ends together. 6. Raise the rear end of snow thrower up to align hanger brackets with holes in back of tractor transaxle. Use clevis pins, washers and hair pins from tractor 3 point hitch. After installing clevis pins, tighten bolts on hanger brackets using two 9/16" open end wrenches. See figure 20. Remove cotter pin and clevis pin from front hanger brackets. Swing brackets open. See figure 21. FIGURE 21 Lower tractor under carriage and install hanging brackets to front cross shaft. See figure 22. Put clevis pin through small hole on hanging brackets to secure brackets around cross shaft. Insert hair pin into hole in clevis pin..to hold pin in position. FIGURE 22 11 FIGURE 23 9. Turn steering wheel to the right to allow _ clearance for guide plate rod. 10. Align holes on guide plate with lower holes on tractor. Slide rod through holes. Secure with hair pin cotters. FIGURE 24 11. Assemble the crank support tubing to the snow thrower housing. Secure in place with two hex bolts (0), lock washers (P) and hex nuts (Q). See figure 24. An adjustable wrench and 1/2" wrench are required. FIGURE 25 12. Place the chute crank bracket (M) in position on the crank support tubing. Slide the chute crank — through the top of crank support tubing. Start hand knob (N) in crank support tubing. See figure 25. 12 FIGURE 26 13. Slip the end of chute crank rod into the universal — joint. Secure with cotter pin (L). See figure 26. 14. Adjust skid shoes to desired position and tighten hex nuts. See adjustment section. 15. Check tire pressure. It may be necessary to put more air into the front tires due to the weight of the snow thrower. OPERAT...
Otros modelos de este manual:Quitanieves - 19967-1 (3.15 mb)