Votos - 2, Puntuación media: 4.5
(
)
)
|
Resumen del manual
14. Use only attachments and accessories approved by the manufacturer of the snow thrower (such as wheel weights, counterweights, or cabs). 15. Never operate the snow thrower without good visibility or light. Always be sure of your footing, and keep a firm hold on the handles. Walk; never run. 16. Never touch a hot engine or muffl er. Clearing a Clogged Discharge Chute Hand contact with the rotating impeller inside the discharge chute is the most common cause of injury associated with snow throwers. Never use your hand to clean out the discharge chute. To clear the chute: 1. SHUT THE ENGINE OFF! 2. Wait 10 seconds to be sure the impeller blades have stopped rotating. 3. Always use a clean-out tool, not your hands. Maintenance and Storage 1. Check shear bolts and other bolts at frequent intervals for proper tightness to be sure the equipment is in safe working condition. 2. Never store the machine with fuel in the fuel tank inside a building where ignition sources are present such as hot water heaters, space heaters, or clothes dryers. Allow the engine to cool before storing in any enclosure. 3. Always refer to operator’s manual for important details if the snow thrower is to be stored for an extended period. 4. Maintain or replace safety and instruction labels, as necessary. 5. Run the machine a few minutes after throwing snow to prevent freeze-up of the collector/impeller. CONGRATULATIONS on your purchase of a new snow thrower. It has been designed, engineered and man u fac tured to give best possible dependability and per for mance. Should you experience any problem you cannot easily remedy, please contact your nearest authorized service center. We have competent, well-trained tech ni cians and the proper tools to service or repair this unit. Please read and retain this manual. The instructions will enable you to assemble and maintain your snow thrower prop er ly. Always observe the “SAFETY RULES”. SERIAL NUMBER: ___________________________ DATE OF PURCHASE: _______________________ THE MODELAND SERIAL NUMBERS WILL BE FOUND ON A DECALATTACHED TO THE REAR OF THE SNOW THROWER HOUSING. YOU SHOULD RECORD BOTH SERIAL NUMBER AND DATE OF PURCHASE AND KEEP IN A SAFE PLACE FOR FUTURE REFERENCE. PRODUCT SPECIFICATIONS Gasoline Capacity 4.0 Quarts (4,54 Liters) and Type: Unleaded Regular only Oil Type SAE 5W-30 or 10W-30 (API SG–SL): (0° to +40°F) SAE 0W-30 (below 0°F) Oil Capacity: 26 Ounces (0,74 Liters) Spark Plug Champion RN4C Gap: 0.030" (0,072 mm) CUSTOMER RESPONSIBILITIES • Read and observe the safety rules. • Follow a regular schedule in maintaining, caring for and using your snow thrower. • Follow the instructions under “Maintenance” and “Storage” sec tions of this own er’s manual. TABLE OF CONTENTS SAFETY RULES ........................................................ 2-3 MAINTENANCE SCHEDULE ..................................... 14 PRODUCT SPECIFICATIONS......................................3 SERVICE AND AD JUST MENTS...........................16-18 CUSTOMER RESPONSIBILITIES................................ 3 STORAGE................................................................... 18 ASSEMBLY / PRE-OPERATION ............................... 5-7 TROU BLE SHOOT ING................................................ 19 OPERATION ............................................................ 8-13 REPAIR PARTS ..................................................... 20-31 MAINTENANCE..................................................... 14-15 WARRANTY................................................................ 32 3 4 PARTS PACKED SEPARATELY IN CARTON ASSEMBLY / PRE-OPERATION Read these instructions and this man u al in its entirety before you attempt to assemble or operate your new snow thrower. Your new snow thrower has been as sem bled at the factory with the ex cep tion of those parts left unassembled for shipping purposes. All parts such as nuts, washers, bolts, etc., necessary to com plete the as sem bly have been placed in the parts bag. To ensure safe and proper operation of your snow thrower, all parts and hard ware you assemble must be tightened se cure ly. Use the correct tools as nec es sary to ensure proper tightness. REMOVE SNOW THROWER FROM CAR TON 1. Remove all accessible loose parts and parts boxes from carton. 2. Cut down all four corners of carton and lay panels flat. 3. Remove all packing materials ex cept plastic tie holding speed control rod to lower handle. 4. Remove snow thrower from carton and check carton thor ough ly for ad di tion al loose parts. HOW TO SET UP YOUR SNOW THROWER TOOL BOX (See Fig. 11) A toolbox is provided on your snow thrower. The toolbox is located on top of the belt cover. Store the extra shear bolts, nuts and multi-wrench provided in parts bag in the toolbox. NOTE: The multi-wrench may be used for assembly of the chute rotator head to snow thrower and making ad just ments to the skid plates. UNFOLD UPPER HANDLE 1. Raise upper handle to the operating position and tight en...