Votos - 3, Puntuación media: 4
(
)
)
|
Resumen del manual
Performance will decrease, and fuel consumption will increase. High altitude performance can be improved by installing a smaller diameter main fuel jet in the carburetor and readjusting the pilot screw. If you always operate the snowblower at altitudes higher than 6,000 feet above sea level, have your authorized Honda Snowblower dealer perform these carburetor modifications. Even with suitable carburetor jetting, engine horsepower will decrease ap- proximately 3.5% for each 1,000 foot increase in altitude. The affect of altitude on horsepower will be greater than this if no carburetor modifica- tion is made. CAUTION: Operation of the snowblower at an altitude lower than the car- buretor is jetted for may result in reduced performance, overheating, and serious engine damage caused by an excessively lean air/fuel mixture. 21 l• Adjust the snow discharge chute to avoid hitting the operator, bystanders, windows, and other objects with thrown snow. Stay clear of the snow discharge chute while the engine is running. l• If the snow discharge chute becomes clogged, stop the engine and use a wooden stick to unclog it. Never put your hand into the snow discharge chute while the engine is running; serious personal injury could result. NOTE: l• To move the machine without engaging the snow-blowing mechanism, squeeze the drive clutch lever only. Do this when moving the machine to or frpm the area to be cleared. l• To engage the snow-blowing machanism without using the drive ‘-mechanism, squeeze the auger clutch lever only. Do this if you wish to maneuver the machine manually while clearing snow. l• Squeeze both levers to propel the machine and clear snow simul- taneotisly. When both levers are squeezed, the drive clutch lever locks the auger clutch lever down (p. 1 1). The auger clutch lever remains lock- ed down so long as qne hand continues to squeeze the drive clutch lever. Releasing the drive clutch lever then unlocks and releases the auger clutch lever. l• If the snow is deeper than the height of the auger, move the machine back and forth to remove snow gradually. l• For best efficiency, clear snow before it melts, refreezes and hardens. DRIVE CLUTCH LEVER Squeeze to engage the drive mechanism AUGER CLUTCH LEVER Squeeze to engage the snow blowing mechanism 7. STOPPING THE ENGINE To stop the engine in an emergency, turn the engine switch OFF immediately. 1. Turn the throttle lever to the SLOW position and turn the engine switch to the OFF position. 2. Turn the fuel valve to the OFF positon. 8. MAINTENANCE The purpose of inspection and maintenance is to keep the snowblower in the best operating condition. Inspect or service as scheduled in the table below. l• Shut off the engine before performing inspection and maintenance, and disconnect the spark plug wire from the plug so the engine cannot be started. l• If the engine must be run, make sure the area is well ventilated. Exhaust gas contains poisonous carbon monoxide; exposure may cause loss of consciousness and may lead to death. CAUTION: l• To.avoid overturning, place the snowblower on a level surface before parforming inspection and maintenance. l• Use only genuine HONDA parts or their equivalent. Replacembnt parts which are not of equivalent quality may damage the snowblower. MAINTENANCE SCHEDULE NOTE: (1) These pans may require more frequent inspection and replacement under heavy use. (2) These items should be serviced by an authorized Honda dealer, unless the owner has the proper took and is mechanically proficient. See the Honda Shop Manual for service information. SPARK PLUG WRENCH ( I WRENCH HANDLE 14 X 10 mm WRENCH 14X 12 mm WRENCH TOOL BAG ENGINE OIL CHANGE Drain the oil while the engine is still warm to assure rapid and complete draining. 1. Remove the drain plug and filler cap, and drain the oil. Retighten the plug securely. 2. Fill the crankcase with the recommended oil (see page 17) and check the level. OIL CAPACITY: 0.6 e (0.63 US qt, 0.53 Imp qt) UPPER LIMIT LOWER LIMIT OIL FILLER CAP c CAUTION: Used motor oil may cause skin cancer if repeatedly left in con- tact with the skin for prolonged periods. Although this is unlikely unless you handle used oil on a daily basis, it is still advisable to thoroughly wash your hands with soap and water as soon as possible after handling used oil. NOTE: Please dispose of used motor oil in a manner that is compatible with the environment. We suggest you take it in a sealed container to your local service station for reclamation. Do not throw it in the trash or pour it on the ground. /; SPARK PLUG SERVICE Recommended spark plug: BPR5ES (NGK). WlGEPB-U (ND) m!am If the engine has been running, the muffler will be very hot. Be careful not to touch the muffler while it is hot. To ensure proper engine operation, the spark plug must be properly gapped and free of deposits. 1. Remove the spark plug cap. 2. Clean any dirt from around the spark plug base. 3. Use the wrench supplied in the tool kit to remove the spark plug....