6. Regular la altura de la maquina quitanieves para evitar areas de gravilla o de pedrisco. 7. No intentar nunca hacer regulaciones mientras el motor este en marcha (excepto cuando esta recomendado especificamente por el fabricante). 8. Llevar siempre gafas de proteccion o mascaras para los ojos durante la utilizacion de la maquina o mientras se haga una regulacion o una reparacion para proteger los ojos de objetos extranos que pueden ser lanzados por la maquina quitanieves. Funcionamiento 1. No

inches. 1 inch = 25.4 mm IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 29 30 REPAIR PARTS SNOW THROWER - MODEL PP11H30ES (96192001400) WHEELS / DECALS 7 32 30 32 30 15 18 17 19 13 20 11 27 27 19 16 20 11 11 11 11 14 15 12 13 18 14 12 4 4 31 34 34 2 8 3 21 33 22 23 24 25 26 28 28 29 10 10 4 4 7 28 28 26 29 25 24 23 22 33 21 9 1 2 3 10 5 3 1 4 2 1 10 7 6 8 9 11 12 REPAIR PARTS SN

23 24 REPAIR PARTS SNOW THROWER - MODEL PP11H30ES (96192001401) HANDLES 32 31 32 30 31 12 10 11 13 15 15 12 16 17 16 23 22 27 27 22 17 11 15 15 14 38 39 40 37 33 35 35 34 34 42 43 44 45 46 46 7 6 36 2 5 5 1 4 4 4 4 8 28 28 9 18 19 20 21 26 24 24 25 5 5 REPAIR PARTS SNOW THROWER - MODEL PP11H30ES (96192001401) HANDLES KEY PART NO. NO. DESCRIPTION 1 405999X479 Lever, Auger Control, RH 2 405783X479 Lever, Traction Drive Control, LH 4 178888 Bushing, Flange 5 169675 Retainer, Hairpin 6 17060408 Scre

• Follow a regular schedule in maintaining, caring for and using your snow thrower. • Follow the instructions under “Maintenance” and “Storage” sec tions of this own er’s manual. TABLE OF CONTENTS SAFETY RULES ........................................................2-3 MAINTENANCE .....................................................14-15 PRODUCT SPECIFICATIONS ......................................3 SERVICE AND AD JUST MENTS ...........................16-18 CUSTOMER RESPONSIBILITIES ...........

inches 1 inch = 25.4 mm 21 22 REPAIR PARTS SNOW THROWER - MODEL NUMBER P8527ESA CONTROL PANEL / DISCHARGE CHUTE 3 2 1 1 2 6 7 4 5 6 16 18 17 10 11 14 13 3 8 15 8 9 12 19 2 2 21 21 22 23 14 26 28 27 27 25 20 29 24 22 23 REPAIR PARTS SNOW THROWER - MODEL NUMBER P8527ESA CONTROL PANEL / DISCHARGE CHUTE KEY PART NO. NO. DESCRIPTION 1 183334 Knob, Lever 2 17501010 Screw #10-24 x 5/8 3 178674 Control Assembly, Deflector 4 73800600 Nut, Lock 3/8-16 5 19131316 Washer, Flat 3/8 6 178659 Control Assembly,

25 26 REPAIR PARTS SNOW THROWER - MODEL PP11530ES (96192001900) DRIVE 4 4 4 4 4 2 2 43 11 1 1 5 22 5 5 2 2 20 41 21 17 13 3 6 14 19 18 18 15 24 36 35 34 37 31 9 12 23 26 29 25 4 4 28 33 32 27 44 REPAIR PARTS SNOW THROWER - MODEL PP11530ES (96192001900) DRIVE KEY PART NO. NO. DESCRIPTION 1 401619 Chain, Drive 2 751153 Nut, Lock 5/16-18 3 402882 Clip, Retainer 4 17490508 Bolt, Hex Head 5/16-18 x 1/2 5 408981 Bearing, Flange 6 12000007 E-Ring, Retainer 9 402855 Sprocket & Shaft Assembly 11 402568 R

Use a stick, NOT YOUR HANDS, to un clog the chute and/or auger. The DIRECTION in which snow is to be thrown is controlled by the discharge chute control lever. • To change the discharge chute position, press downward on discharge chute control lever and move lever left or right until chute is in desired position. Be sure lever springs back and locks into desired position. The DISTANCE that snow is thrown is controlled by the position of the chute deflector. Set the deflector low to throw snow a

5. Contact a qualified service center. Excessive vibration 1. Loose parts or damaged augers or impeller. 1. Tighten all fasteners. Replace damaged parts. If vibration remains, contact a qualified service center. Recoil starter is hard to pull 1. Frozen recoil starter. 1. See “If Recoil Starter Has Frozen” in the Operation section of this manual. Loss of traction drive / slowing of drive speed 1. Drive belt is worn. 2. Drive belt is off of pulley. 3. Friction drive wheel is worn. 1. Check / repla

NO. DESCRIPTION 1 178875X479 Lever, Auger Control, RH 2 178648X479 Lever, Traction Drive Control, LH 3 179439 Nut, Cage 1/4-20 4 178888 Bushing, Flange 5 169675 Retainer, Hairpin 6 180402 Screw, Hex Head 1/4-20 x 3/4 7 178652 Rod, Interlock 8 184003 Tube Assembly, Interlock, RH 9 178651 Tube Assembly, Interlock, LH 10 178645X479 Panel, Control 11 74780524 Screw, Hex Head 5/16-18 x 1-1/2 12 74780528 Screw, Hex Head 5/16-18 x 1-3/4 13 178646X479 Handle Tube, LH 14 178696X479 Handle Tube, RH 15 738

Wipe up any spilled gasoline. 2. REMOVE DISCHARGE CHUTE - Loosen locknut se cur ing chute rotator head to mounting bracket only enough to allow chute rotator head to be raised and dis charge chute to be removed from snow thrower. 3. REMOVE BELT COVER - See “TO REMOVE BELT COVER” in this section of this manual. 4. REMOVE ENGINE PULLEY - Remove bolt, lock wash er and flat washer securing pulley to engine crankshaft. Remove outside (auger) pulley only from crank shaft. 5. SEPARATE SNOW THROWER - Wi