No soltar de golpe la cuerda del arrancador. 6. Cuando el motor arranca, soltar la empunadura del arrancador de retroceso y mover lentamente el mando del obturador hasta la posicion “OFF”. Dejar que el motor se caliente por algunos minutos. El motor no proporcionara la plena potencia hasta que no haya alcanzado la temperatura normal de funcionamiento PUESTA EN MARCHA CON EL MOTOR CALIENTE – ARRANCADOR DE RETROCESO Seguir los pasos descritos arriba, manteniendo el mando del obturador (E) en la po

4. Conectar el cable de potencia al motor (S). 5. Enchufar la otra extremidad del cable de potencia en un enchufe de tres hilos con puesta a tierra de 120 Voltios C.A. 6. Pulsar el cebador (T) tres (3) veces. 7. Pulsar el boton de arranque (U) hasta que el motor se enciende. IMPORTANTE: No hacer girar el motor por mas de 5 segundos continuativamente cada vez que intente poner en marcha el motor. Esperar de 5 a 10 minutos entre cada tentativa. 8. Cuando motor se pone en marcha, soltar boton de ar

The V-belts on your snow thrower are of special construction and should be replaced by original equipment manufacturer (OEM) belts available from your nearest dealer. Using other than OEM belts can cause personal injury or damage to the snow thrower. WARNING: Belt replacement requires separation of the snow thrower. While separating the auger housing (1) from the frame assembly (2), it is important that an assistant stand in the op er - at ing position and hold the snow thrower handles (3). Seri

YOU SHOULD RECORD BOTH SERIAL NUMBER AND DATE OF PURCHASE AND KEEP IN A SAFE PLACE FOR FUTURE REFERENCE. PRODUCT SPECIFICATIONS Gasoline Capacity and Type: .5 Gal (1,89 Liters) Unleaded Regular only Oil Type(API SG–SL): SAE 30 (above 50°F) SAE 5W-30 or 10W-30 (32° to 50°F) SAE 5W-30 (below 32°F) Oil Capacity: 16 Ounces (0,47 Liters) Spark Plug: Gap: F6RTC 0.030" (0,762 mm) CUSTOMER RESPONSIBILITIES • Read and observe the safety rules. • Follow a regular schedule in maintaining, caring for and us

TRACTION DRIVE CONTROL ROD VINYL SLEEVE FIG. 3 PLASTIC TIE NOTE: The multi-wrench may be used for assembly of the chute rotator head to snow thrower and making ad just ments to the skid plates. UNFOLD UPPER HANDLE 1. Raise upper handle to the operating position and tight en handle knobs securely. Additional carriage bolts, washers and handle knobs are in bag of parts. Use to secure upper handle to lower handle. Install in lower holes in handles. INSTALL SPEED CONTROL ROD (See Figs. 1 and 2) 1. R

6. REMOVE HAIRPIN FROM CLUTCH ROD and remove clutch rod from swing plate. Tip swing plate forward. 7. REMOVE AUGER BELT from around pulley. FIG. 20 BELT KEEPER IDLER ARM SQUARE HOLE BOLTS TRACTION DRIVE BELT CLUTCHING IDLER ARM BRACKET AUGER BELT FLAT WASHER AUGER PULLEY AUGER FRAME HOUSING ENGINE PULLEY BOLT FRAME ASSEMBLY AUGER HOUS ING HANDLES 17 SERVICE AND ADJUSTMENTS NOTE: To seal punctures or prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer.

Do not overfill. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. Do not mix oil with gasoline. Purchase fuel in quan ti ties that can be used within 30 days to assure fuel freshness. FIG. 21 PRIM ER SAFETY IG NI TION KEY ON / OFF SWITCH CHOKE CONTROL STARTER BUTTON FUEL SHUT-OFF VALVE NOTE: ALL ITEMS ARE SHOWN IN THEIR TYPICAL LOCATION. ACTUAL LOCATION MAY VARY WITH ENGINE ON YOUR UNIT. POWER CORD PLUG GAS O LINE FILLER CAP ENGINE OIL FILL CAP / DIPSTICK RECOIL (AUXILIAR

Water in engine can result in shortened engine life.. 14 15 SERVICE AND ADJUSTMENTS WARNING: To avoid serious injury, before performing any service or adjust ments: 1. Be sure the on/off switch is in the OFF position. 2. Remove safety ignition key. 3. Make sure the augers and all mov ing parts have completely stopped. 4. Disconnect spark plug wire from spark plug and place wire where it can not come in contact with plug. SNOW THROWER TO ADJUST SNOW THROWER HEIGHT See “TO ADJUST SKID PLATES” and

Damage to the snow thrower can result. • Slower speeds are for heavier snow and faster speeds are for light snow and transporting the snow thrower. It is recommended that you use a slower speed until you are familiar with the operation of the snow thrower. NOTE: When both traction drive and auger control levers are engaged, the traction drive control lever will lock the auger control lever in the engaged position. This will allow you to release your right hand from the handle and adjust the disc

KEY PART NO. NO. DESCRIPTION REPAIR PARTS SNOW THROWER - - MODEL NUMBER MC627ES (96192004100) HANDLES 10 11 1 2 3 4 5 6 7 7 9 9 8 8 12 12 13 13 14 14 01.08.002-F 1 412683X431 CONTROL PANEL 2 424517X431 CONTROL LEVER LH 3 424516X431 CONTROL LEVER RH 4 412679X008 TRACTION ROD ARM 5 426918X008 IMPELLER ROD ARM 6 412677 INTERLOCK BAIL 7 421613 SPACER 8 169675 RETAINER 9 17060410 SCREW 1/4-20 X .62 10 414280 KNOB BLACK 11 414281 KNOB RED 12 178899 HANDLE KNOB 13 19131316 WASHER 3/8 14 72120618 CARRIA