Votos - 4, Puntuación media: 3.8
(
)
)
|
Resumen del manual
5,532,710 and 5,554,998 Made in U.S.A. Winegard Company • 3000 Kirkwood St. • Burlington, IA 52601-2000 319/754-0600 • FAX 319/754-0787 Printed in U.S.A. © Winegard Company 2001 2451099 Rev. 6/05/01 ® OWNER’S MANUAL INSTALLATION INSTRUCTIONS IMPORTANT: INSTALL POINT OF BASE TOWARD FRONT OF VEHICLE! 2 Center Roof Line FIGURE 1 INSTALLATION & ASSEMBLY STEP 1. Choose a location for antenna that will allow it to rest in travel position with top of reflector pointing toward rear of vehicle and to raise and rotate without interfering with other roof-mounted equipment. Make sure inside ceiling area is clear where ceiling plate will mount. NOTE: Figure 1 shows minimum distance (10") antenna should be located from edge of vehicle roof. We recommend you check with your dealer or the manufacturer to see what provisions have been made in the roof for antenna mounting. A reinforced area of roof as well as pre-wire downlead may be available. NOTE: The system must be level for proper operation. If you have a curved roof you should use a Winegard Models RW-1000 IW-1001 wedge kits to level the system. STEP 2. Position template on roof (pg. 15 this manual) and drill a 1-3/4"hole through roof and ceiling of vehicle. Take care to avoid damage to wiring which may run between roof and ceiling. STEP 3. The mount is designed to fit roofs 1" to 6 3/4" thick. Cut elevating shaft and directional handle to size, see table below. CAUTION: IF YOU ARE USING THE RW-1000 ROOF WEDGE, ADD 1/2" TO ELEVATING SHAFT LENGTH GIVEN BELOW, BUT NOT TO THE DIRECTIONAL HANDLE. Front of the RV 26" 34" DIA. OPERATING AREA NOT TO SCALE 17" RADIUS It is highly recomended that the antenna be mounted on roof center line. Do not mount antenna closer than 10" from edge of roof. Vehicle Roof RW-1000 Roof Wedge IW-1001 Antenna Controls Ceiling Wedge 19.50" 3 ROOF ELEVATING SHAFT W/RW-1000 DIRECTIONAL THICKNESS LENGTH HANDLE LENGTH 4 3/4" 6 1/4" RP-4200 req. 5 3/8" 4 1/2" 6" RP-4200 req. 5" 4 1/4" 5 3/4" 6 1/4" 4 3/4" 4" 5 1/2" 6" 4 1/2" 3 3/4" 5 1/4" 5 3/4" 4 1/4" 3 1/2" 5" 5 1/2" 4" 3 1/4" 4 3/4" 5 1/4" 3 9/16" 3" 4 1/2" 5" 3 3/8" 2 3/4" 4 1/4" 4 3/4" 3 1/16" 2 1/2" 4" 4 1/2" 2 3/4" 2 1/4" 3 3/4" 4 1/4" 2 3/8" 2" 3 1/2" 4" 2 1/16" 1 3/4" 3 1/4" 3 3/4" 1 3/4" 1 1/2" 3" 3 1/2" 1 3/8" 1 1/4" 2 3/4" 3" 1" Directional Handle FIGURE 2 NOTE: Make sure that coax cable fits between the reflector and the fixed feed arm. (4) 5/16-18 Hex Nut (4) 5/16" Flat Washer (4) 5/16-18 x 5/8" Flat Head Bolt Rev. 6/05/01 STEP 4. Attach reflector to backup assembly as shown in Figure 2. The mount is designed to fit roofs 1" to 4 3/4" thick. If roof is less than 4 3/4" thick, cut elevating shft and directional handle to size. (See table below.) If roof is more than 4 3/4" thick, contact Winegard Company. CAUTION: IF YOU ARE USING THE RW-1000 ROOF WEDGE, ADD 1/2" TO ELEVATING SHAFT LENGTH GIVEN BELOW, BUT NOT TO THE DIRECTIONAL HANDLE. 4 STEP 6. Attach cable clamp to the coax cable 16" from the cable clamp on the gear housing. STEP 7. Attach cable clamp to roof 3" in front of baseplate as shown in Figure 3, use 7/16" flat washer between screw head and clamp, apply sealing compound over mounting screw head. STEP 8. Feed downlead throught the roof using a Model CE-1000 cover plate (included with hardware), Figure 3A. Weatherproof cable entry by applying sealant under lip of roof-thru plate and where cable enters roof. Attach plate to roof with screws provided. Apply sealant over screws and around edge of roof-thru plate, making sure cable entry is sealed. Secure cables as necessary to prevent whipping. DO NOT MAKE CONNECTION ON TOP OF ROOF unless there is no other option, it is very difficult to weatherproof outside connection. If downlead connection is made on top of roof make sure to weatherproof connection! STEP 9. Assemble ceiling plate, directional handle and crank handle as shown in Figure 5. The circled numbers indicate placement from the ceiling down. Example: The ceiling plate 1 is located next to the ceiling. The elevation crank handle 8 is farthest from the ceiling. The number also indicates sequence of assembly. NOTE: When installing polyethylene shim, # 3, page 5, slide shim onto shaft as far as it will go. Then slide directional handle up over shaft and shim and onto the gear housing. Two shims are supplied in case one is not enough to create a snug fit between directional handle and gear housing. CAUTION: USE CAUTION WHEN INSTALLING THE ELEVATING CRANK. ONCE SCREW TOUCHES SHAFT, TIGHTEN ONLY 1/4 TURN MORE. SCREW SIMPLY HOLDS ELEVATING CRANK ON. DO NOT OVERTIGHTEN! STEP 5. Mount antenna and lift on roof in travel position. Apply a liberal amount of approved nonhardening sealing compound on bottom of base plate and roof area around hole. See Figure 3. Secure base plate with screws provided. Cable clamp on gear housing. CAUTION: DO NOT GET SEALING COMPOUND ON BEARING SURFACE BETWEEN BASE PLATE AND ROTATING GEAR HOUSING. DO NOT PAINT TOP OF BASE PLATE OR AROUND ROTATING GEAR HOU...
Otros modelos de este manual:receptores de satélite - RD-4646 (879.36 kb)