Votos - 2, Puntuación media: 3
(
)
)
|
Resumen del manual
Aprotective cover has been added to the switchplate to guard against damaging electrostatic discharges (ESD), which may occur during installation. Figure 2-11 2.3 Connecting System Components Switchplate Cutout Dimensions 2" Figure 2-11 and the template on the following page have been changed to show the new switchplate cutout dimensions, which have been widened to accommodate the protective cover. Figure 2-13 shows the switchplate connectors as they appear within the new cover. 2.5" (Sticky Note comment KVH 22.05.2003 18:08:50 This addendum applies to products having serial number 03050797 or later.) Input Power Ground (+12 VDC) Figure 2-13 Switchplate Mounting Hole (1 of 2) Switchplate Connectors RJ11 Jack (Data Cable to IRD - Optional) Data/Power Connector Maintenance Port (DB9 Connector) 54-0195 Addendum to Rev. A Appendix C Switchplate Template Appendix C Switchplate Template 2" 2.5" 54-0195 Addendum to Rev. A A Guide to TracVision L2 – ADDENDUM A Guide to TracVision L2 – ADDENDUM (ECO #6040) The following information applies to Revision A of the TracVision L2 Owner’s Manual (KVH Part Number 54-0195). 2 Installation Kitpack Contents Two plugs have been added to the kitpack for sealing the predrilled holes in the antenna baseplate. Part Qty. KVH Part No. Table 2-2 Kitpack Contents Switchplate assembly 1 02-1236-01 Tie-wraps 5 22-0013 RJ11 handset cable 1 32-0724-25 Clam shell ventilator 1 19-0230 #6 x 3.4" thread-forming screws 5 14-0298-12 1.4"-20 x 5.8" hex screws 4 14-0250-10 1.4" flat washers 4 14-0251 3.8" hole plugs 2 19-0282-06 Figure 2-4 2.2 Mounting the Antenna Unit Antenna Baseplate (Bottom View) A step has been added to the antenna mounting Baseplate Holes procedure. The hole plugs need to be installed before mounting the antenna unit to the vehicle. 6. Set aside the antenna unit and clean the roof’s surface to remove any debris. 6b. Seal the two baseplate holes shown in Figure 2-4 with the plugs provided in the kitpack. 54-0195 Addendum to Rev. A Congratulations! Congratulations! ® Industries’ TracVision® L2 is designed for use with DIRECTV®, DISH Network™, and ExpressVu. This manual provides detailed instructions on the proper installation, use, and maintenance of your TracVision L2 system. Throughout this manual, important information is marked for your attention by these icons: . . . . . . . . . . . . . . . . . . . . . . . . . . ... . . . . . . . . . . . . . . . . . . . . ... . . . . . . . . . . . . . . . . . . . . . Direct questions, comments, or suggestions to: KVH Industries, Inc. TracVision L2 Serial Number This serial number will be required for all troubleshooting or service calls made regarding this product. 50 Enterprise Center Middletown, RI 02842 USA Tel: +1 401 847-3327 (Text Box comment Click here to go to our state-of-the-art Customer Support web page...the fastest and easiest way to get all of your questions answered!) Fax: +1 401 849-0045 E-mail: info@kvh.com Internet: If you have any comments regarding this manual, please e-mail them to manuals@kvh.com. Your input is greatly appreciated! KVH Part # 54-0195 Rev. A © 2002, KVH Industries, Inc. TracVisionTracVisionand KVH® are registered trademarks of KVH Industries, Inc. DIRECTV® is an official trademark of DIRECTV, a unit of GM Hughes Electronics Corporation. DISH Network™ is an official trademark of EchoStar Communications Corporation. ExpressVu is a property of Bell ExpressVu, a wholly owned subsidiary of Bell Satellite Services. Table of Contents 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1 1.1 Digital Satellite Television . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1 1.2 TracVision L2 System Overview . . . . . . . . . . . . . . . . . . . . . . . . .1-1 1.2.1 TracVision L2 Components.....................................................1-2 1.2.2 Integrated Receiver/Decoder (IRD) ........................................1-2 1.3 Materials Provided with TracVision L2 . . . . . . . . . . . . . . . . . . . .1-2 1.3.1 Additional Materials Required for TracVision L2 Use .............1-3 2 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-1 2.1 Choosing the Best Location . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-3 2.2 Mounting the Antenna Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-4 2.3 Connecting System Components . . . . . . . . . . . . . . . . . . . . . . . .2-8 2.3.1 Connecting the Antenna to the Switchplate ...........................2-9 2.3.2 Connecting the Antenna to the IRD .......................................2-9 2.3.3 Sealing the Cable Access Hole............................................2-11 2.3.4 Connecting the Switchplate to the IRD ................................2-11 2.3.5 Connecting the Switchplate to Vehicle Power ......................2-12 2.3.6 Connecting the IRD Ground Wire.........................................