Votos - 4, Puntuación media: 3.8
(
)
)
|
Resumen del manual
• AntennatrackstheDIRECTV101Wsatellite,whichislocatedin thesouthernsky. • SystemincludesanintegratedDIRECTVreceiver(withpicture-inguide APG),anRFconverter,andanRFremotecontrol. • Fordetailedinstallationinstructions,refertotheTracVisionA5 InstallationGuide.Forcompleteoperationinstructions,refertothe TracVisionA5User’sGuide. Effective April 2004 Subject to change without notice 54-0239 Rev. A TracVision A5 Shop Manual © 2004 KVH Industries, Inc., All rights reserved. Safe Handling • Twopeoplearerequiredtolifttheantenna.Donottrytoinstallthe antennabyyourself. • Removetheshippingrestraintsfromunderneath,asshowninthe photosabove.Donotfliptheantennaupsidedown. • Nevertilttheantennagreaterthan45°oncetherestraintsare removed. Effective April 2004 Subject to change without notice 54-0239 TracVision A5 Shop Manual © 2004 KVH Industries, Inc., All rights reserved. Mounting to a Roof Rack Flat-head TORX Screws Cover Roof Rack Crossbar Retaining Block Rubber Cushions Swivel Nuts Swivel Nuts Rubber Cushions Flat Washers Lock Nuts Button-head TORX Screws Mounting Bracket Antenna • Positiontheroofrackcrossbars351/2"apart,measuredcenter-tocenter. • Atleast1"clearanceisrequiredbetweentheundersideofthe antennaandtheroof.Toraisetheantennahigher,usethe spacerssuppliedinthekitpack(seepage2.6oftheInstallation Guidefordetails). • Alwaysusethetamper-resistantTORXhardwaresuppliedinthe kitpack.Donotuseanysubstitutes. Effective April 2004 Subject to change without notice 54-0239 TracVision A5 Shop Manual © 2004 KVH Industries, Inc., All rights reserved. Mounting to the Roof Cover Flat-head TORX Screws Mounting Block Jack Nuts Antenna Mounting Bracket Button-head TORX Screws • KVH’sroof-mountkitisdesignedonlyforflatmetalroofsupto 3/16"thick. • Installajacknutinalleight7/16"mountingholes.Ensurethejack nutsaresecurelyattachedtotheroof. • Atleast1"clearanceisrequiredbetweentheundersideofthe antennaandtheroof.Toraisetheantennahigher,usethe spacerssuppliedinthekitpack(seepage3oftheroof-mount instructionsfordetails). • Alwaysusethetamper-resistantTORXhardwaresuppliedinthe kitpack.Donotuseanysubstitutes. Effective April 2004 Subject to change without notice 54-0239 TracVision A5 Shop Manual © 2004 KVH Industries, Inc., All rights reserved. Mounting to Hummer Rack Flat Washer Pin-in-hex Screw Crossbar T-nut (in center channel) Button-head TORX Screws T-nuts 19" Rubber Strips 26.25" Rubber Strip Crossbar • KVH’sHummerkitisdesignedonlyforstandard2"-thickHummer roofrackcrossbars. • Positiontheroofrackcrossbars391/2"apart,measuredcenter-tocenter. • Cuteachcrossbar’srubberstripintothreepiecesasshown above.ThesemeasurementsarecriticaltopositiontheT-nuts properly. • Alwaysusethetamper-resistantTORXandpin-in-hexhardware suppliedinthekitpack.Donotuseanysubstitutes. Effective April 2004 Subject to change without notice 54-0239 TracVision A5 Shop Manual © 2004 KVH Industries, Inc., All rights reserved. Installation Installation Proper Wiring Vehicle Roof Vehicle Power (10-16 VDC) TracVision A5 Wiring Diagram Antenna For detailed system wiring instructions, refer to the TracVision A5 Installation Guide. RF Converter Receiver CAUTION KVH®is a registered trademark of KVH Industries, Inc. HUGHES™is a trademark of Hughes Electronics Corporation. This device complies with Part 15J of the FCC rules. Operation is subject to the following two conditions: (1) This device must not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. ProductWarranty void if outer casing removed. VEHICLE POWER (10-16 VDC) VHF ANTENNA IN S-VIDEO TO KVH TO VIDEO TruSurround, SRS and symbol are trademarks of SRS Labs, Inc. UDIO R AUDIO L VIDEO To Vehicle(Option 3) ANTENNA SATELLITE IN INPUT COMPOSITE VIDEO Service/ Maintenance Only DC Power Ground To Vehicle Video(Option 1) To Vehicle Video (Option 1) To Vehicle Video To Vehicle Video (Option 2) To VHF Antenna (Optional) Fuse RF REMOTE OUT TO TV TO IRD SATELLITE IN DIAGNOSTIC PORT 1 DIAGNOSTIC PORT 2 Audio • Ifyoumustcuttheantennacable,terminatethecablewiththe suppliedSnap-N-Seal®F-connector.Low-qualityconnectorswill degradesystemperformance. Augat Tool • AlwaysuseanAugattool(KVHP/N19-0242) toattachF-connectors. • Donotkinkorstresstheantennacable. • Tightenallconnectionsadequately. • Usehigh-qualityvideocablebetweenreceiverandmonitor(s). • PlacetheRFconverteratleast3feetawayfromthereceiverand otherelectronicdevices. Effective April 2004 Subject to change without notice 54-0239 TracVision A5 Shop Manual © 2004 KVH Industries, Inc., All rights reserved. Connecting to Power Before you start: • Beforeconnectingthepowercable,removethekeyfromthe ignitionandremovethenegativeleadfromthevehiclebattery. Connecting the receiver power cable’s red (positive) wire: • Connecttheredwireto+12VDCswitched(accessory)power. Withthevehiclerunningandthereceiverturnedon,poweratthe receivermustmeasureatleast11VDC. • Donotwireanyotherdevicetothesamepowercircuit. Connecti...