Votos - 5, Puntuación media: 4.4
(
)
)
|
Resumen del manual
1.3 Materials Provided with TracVision C3 The data/power cable supplied with the system is 28 ft (8.5 m) in length. The RF cable supplied with the system is 50 ft (15 m) in length. Table 1-3 has been updated to show the correct cable lengths. Component KVH Part No. Table 1-3 Antenna Unit (comprising): 01-0225-20† 01-0225-23†† 01-0225-26††† 01-0225-29†††† TracVision C3 Packing List Baseplate Assembly 02-1245-01* 02-1245-03** Radome Assembly 02-0953-04 RF Cable (50 ft/15 m) Data/Power Cable (28 ft/8.5 m) 32-0417-50 32-0730-28 Cables for the TracVision C3 are stored beneath the antenna unit PC Cable (6 ft/1.8 m) 32-0628-06 during shipping. Mounting Plate 20-0684 Kitpack*** 72-0102 Owner’s Manual 54-0159 IRD Ground Wire 32-0583-50 Switchplate 02-1023-01 TV/SAT Switch (optional) 01-0245 † European TracVision C3 system †† North American TracVision C3 system (defaulted to DIRECTV) ††† North American TracVision C3 system (defaulted to DISH Network) †††† North American TracVision C3 system (defaulted to ExpressVu) * Baseplate assembly with single-output LNB ** Baseplate assembly with dual-output LNB *** A complete listing of kitpack contents is provided in Table 2-2. 54-0159 Addendum to Rev.G 5.3 5.3 Table 5-1 has been updated to show the new part numbers for the data/power cable, RF cable, RF PCB, and European LNB. Part Name Part Number Table 5-1 Field Replaceable Units Baseplate Assembly 02-1245-01* 02-1245-03** Radome Assembly 02-0953-04 Data/Power Cable 32-0730-28 RF Cable 32-0417-50 PC Cable 32-0628-06 CPU PCB 02-1043-02 RF PCB 02-1524 Antenna Gyro 02-1035 Antenna Gyro Gasket 24-0139 System Fuses 16-0017-3150 LNB (European system) 19-0346 LNB (N. American system) 19-0056 Switchplate 02-1023-01 TV/SAT Switch (optional) 01-0245 * Baseplate assembly with single-output LNB ** Baseplate assembly with dual-output LNB 54-0159 Addendum to Rev.G TracVision C3 Owner’s Manual Addendum TracVision C3 Owner’s Manual Addendum The following information applies to Revision G of the TracVision C3 Owner’s Manual (KVH Part Number 54-0159). Your TracVision C3 system has the capability to automatically switch between the Echo 119 and Echo 110 satellites in DISH 500 mode. DISH 500 Mode When a compatible DISH Network™ receiver* is connected to the TracVision antenna’s RF1 connector, and the antenna is configured for DISH 500 mode, you can switch between the Echo 119 and Echo 110 satellites using the receiver’s remote control. * All new DISH Network receiver models should be compatible with the TracVision antenna’s DISH 500 mode. The following models have been proven compatible by KVH: DishPro 301, 311, and 811. Configuring the Antenna for DISH 500 Mode To configure the TracVision antenna for DISH 500 mode, you will need to run the receiver’s Check Switch function twice. You do not need a laptop computer. To configure the TracVision antenna for DISH 500 mode, follow the steps below. 1. Stop your vessel in a blockage-free area and do not move the vessel until you have completed the entire configuration process. 2. Turn on the master receiver (the receiver that is connected to the antenna’s RF1 connector) and the television. 3. Turn on the TracVision antenna using the switchplate’s power switch. 4. Wait one minute for the antenna to initialize. (Sticky Note comment KVH 25.05.2005 16:57:25 This addendum applies to products having serial number 050402252 or later.) NETWORK 54-0159 Addendum to Rev.G 5. Using the receiver’s remote control, go to the “Point Dish/Signal Strength” screen (press Menu, 6, 1, 1 (on most models)). 6. Using the remote control’s arrow buttons, highlight “Check Switch” and press the Select button. 7. Highlight “Test” and press Select. 8. Wait a minimum of 15 minutes for the Check Switch function to complete and for the antenna to restart and configure itself for DISH 500 mode. If the Check Switch function fails (the receiver locks up), disconnect power from the receiver, restart the antenna, then restore power to the receiver and try the Check Switch function again. 9. Run the Check Switch function a second time. This allows the receiver to configure itself for automatic satellite switching. 10. Wait until the Check Switch function is complete (it will take a couple minutes). 11. Ensure that the following is displayed on the TV: Installed Switch: SW42 Input: 1 1 2 2 Satellite: 119 119 110 110 Polarity: Odd Even Odd Even Status: Satellite reception verified This indicates that the receiver is configured properly. If this information is not displayed exactly as shown above, try running the Check Switch function again. 12. Exit the menu and allow the receiver to download the program guide. 13. Once the program guide has loaded, you can start enjoying satellite TV. The antenna will switch between satellites automatically as you change channels using the receiver’s remote control. 54-0159 Addendum to Rev.G TracVision C3 Owner’s Manual Addendum TracVision C3 Owner’s Manual Addendum The following information applies to Revis...