Votos - , Puntuación media:
(
)
)
Fabricar: Sony
Tamaño del archivo: 117.6 kb
Nombre del archivo: 4246665111.pdf
Idioma del manual:
El documento se está cargando, por favor, espere
 |
El documento se está cargando, por favor, espere
Otros manuales para este modelo:
Resumen del manual
Better measures. If the problem persists, consult your nearest surround effect will result if all speakers are set at the Sony dealer. same distance from the listening position. Place the front speakers at a suitable distance to the left and right of the television. There is no sound from the speaker system. Place the subwoofer on either side of the television. •Make sure all the connections have been Place the center speaker on the top-center of the TV set. correctly made. The placement of surround speakers greatly depends on •Make sure the volume on the amplifier has the configuration of the room. The surround speakers may be placed on both sides of the listening position A been turned up properly. or behind the listening position B. •Make sure the program source selector on the amplifier is set to the proper source. Tips •Check if headphones are connected. If they • Movies are best enjoyed in a room that produces no are, disconnect them. echoes (as in one with surrounding curtains). • Music (especially classical music) is best enjoyed in a There is distortion in the subwoofer sound room that produces some echo. output. •Check if any sound-enhancing functions have Setting the speakers been activated on the amplifier. If they have, turn them off. Attaching the speaker pads (D) To prevent speaker vibration or movement while There is hum or noise in the speaker output. listening, attach the supplied foot pads to the bottom four •Make sure all the connections have been corners of the center speaker, front speakers, and correctly made. surround speakers. •Make sure none of the audio components are Setting the center speaker (E) positioned too close to the TV set. Set the center speaker firmly on top of the TV set. Make sure it is completely level. The sound has suddenly stopped. •Make sure all the connections have been Setting other speakers (F) correctly made. Contact between bare speaker For greater flexibility in the positioning of the speakers, wires at the speaker terminals may cause a use the optional WS-FV10D or WS-WV10D speaker stand short-circuit. (available only in certain countries). Tip (G) Specifications The height of the front speakers should be adjusted to about the center of the TV screen. SS-MS145 (Front and surround speakers) Setting the amplifier Speaker system Full range, magnetically shielded Speaker units 5.5 . 11 cm, cone type When connecting to an amplifier with internal multi Enclosure type Bass reflex channel decoders (Dolby Digital, DTS**, etc.), you should Rated impedance 8 ohms use the setup menus for the amplifier to specify the Power handling capacity parameters of your speaker system. Maximum input power: 100 watts See the table below for the proper settings. For details on Sensitivity level 86 dB (1 W, 1 m) the setting procedure, refer to the manual that was Frequency range 28 Hz - 20,000 Hz provided with your amplifier. Dimensions (w/h/d) Approx. 76 . 162 . Speaker setup 106 mm, including front grille For Set to Mass Approx. 0.8kg each Front speakers SMALL SS-CN145 (Center speaker) Center speaker SMALL Speaker system Full range, Surround speakers SMALL magnetically shielded Subwoofer ON (or YES) Speaker units 5.5 . 11 cm, cone type Enclosure type Bass reflex Rated impedance 8 ohms If you use the amplifier with adjustable crossover Power handling capacity frequency, it is recommended to select 120 Hz (or close to Maximum input power: 100 watts this figure) as the crossover frequency for your front, Sensitivity level 86 dB (1 W, 1 m) center, and surround speakers. Frequency range 28 Hz - 20,000 Hz Dimensions (w/h/d) Approx. 280 . 82 . ** “DTS” and “DTS Digital Surround” are registered 106 mm, including front trademarks of Digital Theater Systems, Inc. grille Mass Approx. 1.0 kg Listening to the sound (H) SA-WMS145 (subwoofer) Speaker system Active subwoofer, First, turn down the volume on the amplifier. The magnetically shielded volume should be set to minimum before you start Speaker unit Woofer: 20 cm, cone type playing the program source. Enclosure type Advanced SAW type Amplifire section Continuous RMS power output 1 Turn on the amplifier and select the 100 W (6 ohms, program source. 20 - 250 Hz, 0.8% THD) Reproduction frequency range 28 Hz - 200 Hz 2 Press POWER on the subwoofer. High frequency cut-off frequency The POWER indicator on the subwoofer 150 Hz lights up green. Inputs INPUT (input pin jack) 3 Play the program source. General Power requirements 230 V AC, 50/60 Hz Power consumptions 100 W Dimensions (w/h/d) Approx. 270 . 325 . 398 mm, including front grille Adjusting the subwoofer (H) Mass Approx. 10 kg Supplied accessories Foot pads (20) Rotate LEVEL to adjust the volume. Monaural connecting cord (1 phono to 1 phono) (1) Set the volume level to best suit your Speaker connecting cords, 10 m (2) preference according to the program source. Speaker connecting cords, 3.5 m (3) Design and specifications are subject to change without Notes notice. • Some amplifier functi...
Otros modelos de este manual:- ()