Votos - 4, Puntuación media: 4.3
(
)
)
|
Resumen del manual
Alignment of longitudinal bed slide ways in vertical plane: 0.04mm (0.0015") 0.018mm b. Parallelism of transverse direction: 0.04mm (0.0015") in 1000mm (39.370") 0.03mm 0.0007" 0.0012" G2 Parallelism of tailstock to longitudinal motion carriage: a. In vertical plane 0.02mm in 500 mm b. In horizontal plane 0.02mm (0.0008") in 500mm (19.685") 0.01mm 0.01mm 0.0004" 0.0004" G3 Cam action of spindle 0.015mm (0.0006") 0.008mm 0.0003" G4 Spindle nose runout 0.01mm (.0004") 0.005mm 0.0002" G5 Spindle taper runout: a. At end of spindle nose 0 to 0.01mm (0.0004") b. At end of 300mm (11.811") test bar 0 to 0.02mm (0.0007") 0.005mm 0.018mm 0.0002" 0.0007" G6 Parallelism of spindle center line to longitudinal motion of carriage: a. In vertical plane: 0.02mm (0.0007") in 300mm (11.811") b. In horizontal plane: 0.015mm (0.0006") in 300mm 0.005mm 0.013mm 0.0002" 0.0005" G7 Spindle center runout: 0.015mm (0.0006") 0.01mm 0.0003" G0509G Precision Lathe Inspection Record -2- No. Diagram of Measuring Method Allowed Tolerances Typical Measured Value (mm) Typical Measured Value (inch) G8 Parallelism of center line of tailstock spindle to longitudinal motion of carriage: a. In vertical plane: 0.02mm (0.0007") in 100mm (3.937") b. In horizontal plane: 0.015mm (0.0006") in 100mm 0.007mm 0.005mm 0.00027" 0.0002" G9 Parallelism of center line of tailstock spindle hole to longitudinal motion of carriage: a. In vertical plane: 0.03mm (0.001") in 300mm (11.811") b. In horizontal plane: 0.03mm (0.001") in 300mm (11.811") 0.015mm 0.01mm 0.0006" 0.0003" G10 Difference in center height between headstock and tailstock: 0.04mm (0.0015") 0.04mm 0.0015" G11 Parallelism of spindle axis with longitudinal movement of upper slide 0.015mm (0.0006") in 150mm (5.905") 0.01mm 0.0003" G12 Cross slide alignment to face follow or conave only on 160mm (6.300") diameter 0.02mm (0.0007") 0.008mm 0.0003" G13 Lead screw parallel with ways 0 to 0.10mm horizontal (0.004" 0 to 0.10mm vertical (0.004") 0.05mm 0.07mm 0.0019" 0.0027" G14 Lead screw alignment of half nut 0 to 0.10mm horizontal (0.004") 0 to 0.10mm vertical (0.004") 0.07mm 0.08mm 0.0027" 0.0031" G0509G Precision Lathe Inspection Record -3- No. Diagram of Measuring Method Allowed Tolerances Typical Measured Value (mm) Typical Measured Value (inch) G15 Lead screw cam action 0.015mm (0.0006") 0.01mm 0.0003" P1 Accuracy of outside round cutting: a. Roundness: 0.005mm b. Cylindricity: 0.02mm (0.0007") in 200mm (7.874") 0.003mm 0.01mm 0.0001" 0.0003" P2 Flatness of face for finishing cutting: 0.025mm (0.001") on the diameter of 300mm (11.811") 0.015mm 0.0005" P3 Accuracy of pitch of leadscrew thread 0.04mm (0.0015") in 200mm (7.874") 0.02mm (0.0007") in 50mm (1.968") 0.02mm 0.01mm .0007" .0003" G0509G Precision Lathe Inspection Record -4-...