Votos - 4, Puntuación media: 4.5
(
)
)
|
Resumen del manual
Installing the washer on any type of carpeting, soft tile, a platform or other weakly supported structures is not recommended. Place a level on the cabinet top and check if the washer is level from side to side and front to back. NOTE: Level must rest on raised portion of top panel. Refer to Figure 3. If washer is not level, tilt washer to access the front and rear leveling legs. For easier access to leveling legs, prop up washer with a wooden block. Refer to Figure 3. Loosen 7/8 in. locknut and adjust legs until the washer is level from side to side and front to back (using a level). Washer should not rock. Tighten the locknuts securely against the washer base using the 7/8 in. wrench. If the locknuts are not tight, washer will move out of position during operation. 802951 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 7 Installation NOTE: DO NOT slide washer across floor if the leveling legs have been extended, as legs and base could become damaged. Remove rubber feet from accessories bag and place on all four leveling legs. Verify that unit doesn’t rock. Figure 3 FLW2114N 1 Leveling Leg 2 Washer Base 3 Level 4 Wood Block 5 Locknut 6 Rubber Foot 2 1 3 56 4 Step 3: Connect Fill Hoses WARNING Under certain conditions, hydrogen gas may be produced in a hot water systemthat has not been used for two weeks or more. HYDROGEN GAS IS EXPLOSIVE. If the hot water system has not been used for such a period and before using the washer, turn on all hot water faucets and let the water flow from each for several minutes. This will release any accumulated hydrogen gas. The gas isflammable. Do not smoke or use an open flame during this time. W029 Water Supply Water supply faucets must fit standard 3/4 inch (19.1 mm) female garden hose couplings. DO NOT USE SLIP-ON OR CLAMP-ON CONNECTIONS. Water supply faucets should be readily accessible to permit turning them off when washer is not being used. Recommended cold water temperature is 60° to 80° Fahrenheit (16° to 27 Celsius). Recommended maximum hot water temperature is 125° Fahrenheit (51° Celsius). Warm water is a mixture of hot and cold water. Warm water temperature is dependent upon water temperature and pressure of both the hot and cold water supply lines. WARNING To prevent personal injury, avoid contact with inlet water temperatures higher than 125° Fahrenheit (51° Celsius) and hot surfaces. W748 Water pressure must be a minimum of 20 to a maximum of 120 pounds per square inch (138 to 827 kPa) static pressure measured at the faucet. NOTE: Water pressure under 20 pounds per square inch (138 kPa) will cause an extended fill time in the washer and may not properly flush out the detergent dispenser. 8 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 802951 Installation 802951 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 9 Turn on the water supply faucets and flush the lines for approximately two minutes to remove any foreign materials that could clog the screens in the water mixing valve. NOTE: When installing in newly constructed or renovated building, it is very important to flush the lines since build-up may have occurred during construction. Connecting Hoses Insert each filter screen into the end of each fill hose that will connect to the water supply faucet. The screen must be facing outward. Refer to Figure 4. Insert each plain rubber washer into the other end of each fill hose that will connect to the water mixing valve at the rear of the washer. Refer to Figure 4. Thread hose couplings onto valve connections fingertight, then approximately 1/4 turn with pliers. IMPORTANT: DO NOT cross thread or overtighten couplings. Turn water on and check for leaks. If leaks are found, retighten the hose couplings. Continue tightening and rechecking until no leaks are found. Figure 4 IMPORTANT: Hoses and other natural rubber parts deteriorate after extended use. Hoses may develop cracks, blisters or material wear from the temperature and constant high pressure they are subjected to. All hoses should be checked on a monthly basis for any visible signs of deterioration. Any hose showing the signs of deterioration listed above should be replaced immediately. All hoses should be replaced every five years. Figure 5 IMPORTANT: Turn off water supply faucets after check-out and demonstration. Owner should turn off water supply whenever there will be an extended period of non-use. NOTE: Longer fill hoses are available (as optional equipment at extra cost) if the hoses supplied with the washer are not long enough for the installation. Order hoses as follows: No. 20617 Fill Hose (8 feet) (2.44 m) No. 20618 Fill Hose (10 feet) (3.05 m) TLW1976N 1 Faucet 2 Fill Hoses 3 Plain Rubber Washer 4 Filter Screens HOT COLD 2 1 3 4 FLW1974N 1 Water Supply Faucets 2 Hot Water Connection 3 Cold Water Connection 4 Fill Hoses FLW1974N 2 1 3 4 WATER MIXING VALVE Installation Risers Step 4: (Non-Gravity Drain Models Only) Connect Drain Hose to ...