Votos - 3, Puntuación media: 4
(
)
)
|
Resumen del manual
Keeping the door open after a wash will also help to preserve the door seal. Maintenance wash With the use of low temperature washes it is possible to get a build up of residues inside the drum. We recommend that a maintenance wash be performed on a regular basis. To run a maintenance wash: . The drum should be empty of laundry. . Select the hottest cotton wash programme. . Use a normal measure of detergent, must be a powder (such as Ariel Futur). External cleaning Clean the exterior cabinet of the appliance with soap and water only, and then dry thoroughly. Cleaning the dispenser drawer The washing powder and additive dispenser drawer should be cleaned regularly. Remove the drawer by pressing the catch downwards and by pulling it out. Flush it out under a tap, to remove any traces of accumulated powder. To aid cleaning, the top part of the additive compartment should be removed. Cleaning the drawer recess Having removed the drawer, use a small brush to clean the recess, ensuring that all washing powder residue is removed from the upper and lower part of the recess. Replace the drawer and run the rinse programme without any clothes in the drum. Cleaning the pump The pump should be inspected if • The machine does not empty and/or spin • The machine makes an unusual noise during draining due to objects such as safety pins, coins etc. blocking the pump. Proceed as follows: • Disconnect the appliance. • If necessary wait until the water has cooled down. . . . . • Place a container close to the pump (A) to collect any spillage. • Pull out the emergency emptying hose (B), place it in the container and remove its cap. 16 • When no more water comes out, unscrew the pump Turn off the water tap. Unscrew the water inlet hose. cover and remove it. Always keep a rag nearby to dry Clean the filter using a hard bristle brush. up spillage of water when removing the cover. Tighten up the inlet hose. . • Remove any objects from the pump impeller by rotating it. . • Refit the cap on the emergency emptying hose and place the latter back in its seat. . • Screw the pump cover fully in. Warning When the appliance is in use and depending on the programme selected there can be hot water in the pump. Never remove the pump cover during a wash cycle, always wait until the appliance has finished the cycle, and is empty. When replacing the cover, ensure it is securely retightened so as to stop leaks and young children being able to remove it. Cleaning the water inlet filter If your water is very hard or contains traces of lime deposit, the water inlet filter may become clogged. It is therefore a good idea to clean it from time to time. The dangers of freezing If the machine is exposed to temperatures below 0°C, certain precautions should be taken. . Turn off the water tap. . Unscrew the inlet hose. . Place the end of the emergency emptying hose and that of the inlet hose in a bowl placed on the floor and let water drain out. . Screw the water inlet hose back on and reposition the emergency emptying hose after having put the cap on again. . When you intend to start the machine up again, make sure that the room temperature is above 0°C. Emergency emptying out If the water is not discharged, proceed as follows to empty out the machine: • Pull out the plug from the power socket; • Close the water tap; • If necessary, wait until the water has cooled down; • Place a bowl on the floor and place the end of the emergency emptying hose into the bowl. Remove its cap. The water should drain by gravity into the bowl. When the bowl is full, refit the cap on the hose. Empty the bowl. Repeat the procedure until water stops flowing out; • Clean the pump if necessary as previously described; • Replace the emergency emptying hose in its seat after having plugged it; • Screw the pump cover again. 17 Something not working Please carry out the following checks before contacting your local Service Force agent. IMPORTANT: If you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or installation, a charge will be made even if the appliance is under guarantee. During machine operation it is possible that the red Start/Pause pilot light flashes, one of the following alarm codes appears on the display and some acoustic signals sound to indicate that the machine is not working: -E EE1 110 00: problem with the water supply -E EE2 220 00: problem with water draining -E EE4 440 00: door open Once the problem has been eliminated, press the “Start/Pause” button to restart the programme. If after all checks, the problem persists, contact your local Service Force Centre. Symptom Solution The machine does not start . The door has not been closed. (E EE 4 44 0 00 ) . The plug is not properly inserted in the power socket. . There is no supply at the socket. . The main fuse or the fuse in the plug has blown. . The «Start/Pause» button has not been pressed. . The «Delay start» option has been selected. . The «Child lock» option has ...