Votos - 2, Puntuación media: 4.5
(
)
)
|
Resumen del manual
This appliance is equipped with a cord having and equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. WARNING- Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified or service representative or personnel if you are in doubt as to whether the appliance is properly grounded. Do not modify the plug provided with the appliance: if it will not fit the outlet, have a proper outlet installed by a qualified electrician. Electrical Specifications: Voltage/Amperage - 115V, 12 Amp, 60 Hz 3 Prong plug attached to the appliance in the factory Circuit/Protection - 3 wires single phase, 120V, 60 Hz, AC separate 15 amp circuit or greater. Recessed, Closet and Alcove Installations This appliance may be installed in a recessed area, closet or alcove. All measurements are in inches. • If the appliance is to be installed in a closet with zero clearance on the side of the appliance, a total of 12 square inches of free air space movement to the back of the unit must be allowed into the closet. • If a door is to be installed that potentially encloses the unit while running, the door must allow for a minimum of 20 square inches of free air movement. There must also be a 1” space from the front of the unit to the closed door and 1” from the back of the unit to the wall. Additional spacing should be considered for easy installation, servicing, removal and compliance with applicable local, state and federal codes. • The floor must be able to support at least 280 lbs and a surface that is solid and level. If machine is to be placed in cabinet, up off the floor, it may be necessry to secure the drum with a tether to prevent excessive drum movement. Plese call Majestic Appliances for more information. • Installations in RV’s or Marine pleasure craft suggest that the machine might best be installed midships in the boat, or over the axles of the RV where movement is at a minimum. Adequate blocking should prevent extreme movement when installed in an RV or Marine pleasure craft. Electricity If the appliance is to be installed in a closet, the installation must be completed by a qualified person or service representative. Additional clearances for floor, wall or door moldings may be required. Page 3 Installing/Removing Getting things ready to install your appliance (continued) Plumbing - Water, Drains WATER CONNECTION 1. This appliance can be used with either hot/cold or cold/cold connections. 2. The hoses supplied have either a straight end or an elbow end. The elbow end is meant to connect to the washer. Be sure to connect the hot hose to the hot side of the appliance itself, the cold side to the cold connection. (See picture) The straight end to the 3/4” BSP standard hose bib thread. 3. MAKE SURE WASHERS ARE INSTALLED IN EACH END OF THE SUPPLY HOSES. 4. Ensure that water connections are free from debris or sediment. 6. BRASS PRESSURE REDUCERS MUST BE INSTALLED TO PROTECT COMPONENTS INSIDE THE APPLIANCE.IMPORTANT ! CHECK THREADS ON THE MACHINE, THE BRASS PRESSURE REDUCERS AND THE SUPPLY HOSES TO ENSURE THEY ARE CLEAN. DO NOT USE EXCESSIVE FORCES. TIGHTEN BY HAND. DO NOT USE POWER TOOLS. Connection of the drain hose to standpipe • Outlet end of drain hose (See figure 2) must be at least 20” above bottom of washer. Do NOT block top of standpipe closed with tape or other materials. An air break must be provided at the standpipe to avoid siphoning. • Connect the drain hose to a standpipe (with internal diameter of at least 3.2 cm or 1 1/4” min. diameter) with a minimum carry away volume of 7 gallons. The top of the standpipe must be 20” minimum from the botton of the appliance. Place drain hose for drainage into a sink tub or standpipe, ensuring that there are no kinks or bends. The free end must be at a height of 80 cm (31 1/2”) from the floor, the hose must be fixed in the appropriate hook on the upper part of the back panel (fig.4) DO NOT INSERT THE END IF THE DRAIN HOSE MORE THAN 6” INTO THE STANDPIPE. INSERTING MORE MAY CAUSE THE APPLIANCES TO HAVE INSUFFICIENT DRAINAGE. CORRECT LEVELING OF UNIT IS ESSENTIAL It is important for the machine to be perfectly level. The angle of inclination on the work surface must not be more than 2 degrees. For this reason the machine is fitted with adjustable feet used for leveling the machine before use. In the case of carpeted flooring, remember to check that the ventilation in the support area is not plugged. Exhaust Duct Installation • Check that all ducting is lint free. Secure ducting with clamps or metal tape. • The exhaust duct must end with an approved exhaust vent hood with swing out dampers or appropriate louvers. • Flex or rigid metalic ducting is recommended. • Exhaust duct should be short and straight and slope downwards and away from the appliance. Long exhaust duct runs can increase d...
Otros modelos de este manual:Lavadoras - MJ-9000VG (298.94 kb)