Votos - 2, Puntuación media: 4.5
(
)
)
|
Resumen del manual
Wipe tub with a nonabrasive household cleanser, then rinse. Shake or brush excess dirt and sand from items before washing. Wash load too wet after spin. Washer is overloaded. Do not overload washer. See Washing Procedures. Load is out of balance. Rearrange load to allow proper spinning. Drain hose is kinked. Straighten drain hose. Water does not enter washer or it enters slowly. Water supply is not adequate in area. Check another faucet in the house. Wait until water supply and pressure increase. Water supply faucets are not completely open. Fully open hot and cold faucets. Water is being used elsewhere in the house. Water pressure must be at least 30 psi (260 kPa). Avoid running water elsewhere while washer is filling. Water inlet hoses are kinked. Straighten hoses. Water level does not cover load. Improper water level selection (for models with water level/load size control). Select higher water level/load size. Washer is overloaded. Do not overload washer. When control is set at highest fill level, dry load level should not be higher than top row of circular holes in wash tub. Warm or hot water is not hot enough. Hot water heater is set too low or is a distance from laundry center. Measure hot water temperature at nearby faucet with candy or meat thermometer. Water temperature should be at least 130°F (70°C). Adjust water heater as necessary. Hot water is being used elsewhere in the house. Avoid using hot water elsewhere before or during washer use. There may not be enough hot water available for proper cleaning. If problem persists, your hot water system may be unable to support more than 1 use at a time. Drain hose is kinked or clogged. Clean and straighten the drain hose. Water in washer does not drain or drains slowly. Fill hose connection at faucet or washer. Check and tighten hose connections. Install rubber sealing washers provided. Water leaks. House drain pipes are clogged. Unclog drain pipes. Contact plumber if necessary. Oversudsing. Use less detergent. Incorrect wash and rinse temperatures. Hot and cold water hoses are connected to wrong supply faucets. Connect hot water hose to hot water faucet and cold water hose to cold water faucet. Water is entering washer but tub does not fill. Drain hose standpipe is incorrect height. Standpipe must be a minimum of 33" (83.82 cm) high to prevent siphoning. See INSTALLATION INSTRUCTIONS. 14 OCCURRENCE OCCURRENCEOCCURRENCEOCCURRENCEOCCURRENCEOCCURRENCE POSSIBLE CAUSE OCCURRENCEOCCURRENCEOCCURRENCEOCCURRENCEOCCURRENCE SOLUTION SOLUTIONSOLUTIONSOLUTIONSOLUTIONSOLUTION DRYER DRYERDRYERDRYERDRYERDRYER Dryer does not start. Electrical power cord is not securely plugged in or plug may be loose. Make sure the plug fits tightly in wall outlet. House fuse blown or circuit breaker tripped. Reset circuit breaker or replace fuse. Make sure electrical line is not overloaded and the dryer is on a separate circuit. Thermal limiter tripped. Call authorized service person for replacement. Dryer runs but won't heat. There are 2 house fuses in the dryer circuit. If 1 of the 2 fuses is blown, the drum may turn but the heater will not operate. Replace fuse. Gas supply valve is not open (gas models). Check to make sure supply valve is open. See INSTALLATION INSTRUCTIONS for procedure. Dryer does not have enough air supply to support the burner flame (gas models). See INSTALLATION INSTRUCTIONS. LP gas supply tank is empty or there has been a utility interruption of natural gas (gas models). Refill or replace tank. Dryer should heat when utility service is restored. Drying cycle takes too long, outside of the dryer feels too hot or smells hot. Lint screen is clogged with lint. Exhaust duct requirements have not been met. Make sure all lint has been removed from the dryer lint screen before starting each cycle. Exhaust duct must be at least 4 inches in diameter and made of rigid or flexible metal. When in place, the duct must have no more than two 90° bends and must not exceed length listed in INSTALLATION INSTRUCTIONS. Electric dryer is connected to a 208 volt circuit. Drying time will be 20% longer than drying on a 240 volt circuit. Drying procedures have not been followed. See Drying Procedures, page 10. Outside exhaust hood or exhaust duct may be clogged or restricted. Clean out any obstruction. Excessive wrinkling. High humidity. Dryer is overloaded. Use a dehumidifier near the dryer. Do not overload. See Drying Procedures, page 10. Items left in dryer too long. Remove items as soon as cycle ends. Insufficient sorting of items. See Drying Procedures, page 10. Drying temperature too high. Follow fabric care label instructions. 15 LAUNDRY CENTER WARRANTOR: ELECTROLUX HOME PRODUCTS CANADA 6150 McLaughlin Road, Unit#1 Mississauga, Ontario L5R 4C2 WARRANTY PERIOD: For the first year after purchase by the original consumer/ owner: For twenty five years after purchase by the original consumer/owner: Washer transmission for the second through fifth year after purchase by the origin...