Votos - 5, Puntuación media: 4
(
)
)
|
Resumen del manual
Refer to 'Instal- lation'. The load is very small. Add more laundry in the drum. ENGLISH 29 Problem Possible cause Possible solution The appliance fills with water and drain immediately. The end of the drain hose is too low. Make sure that the drain hose is in the correct position. The washing results are not satis- The detergent you used was not sufficient or cor- Increase the detergent quantity or use a different one. factory. rect. You did not remove the stubborn stains before Use special products to remove the stubborn stains. you wash the laundry. Incorrect temperature was set. Make sure that you set the correct temperature. Too much laundry load. Decrease the laundry load. After the check, activate the appliance. If the display shows other alarm codes, The programme continues from the contact the service centre. point of interruption. If the problem occurs again, contact the service centre. INSTALLATION UNPACKING 1. Use the gloves. Remove the external film. If necessary, use a cutter. 2. Remove the cardboard top. 3. Remove the polystyrene packaging materials. 4. Remove the internal film. 5. Open the door. Remove the polystyrene piece from the door seal and all the items from the drum. 6. Put the front piece on the floor behind the appliance. Carefully put down the appliance with the rear side on it. Make sure not to damage the hoses. 1 2 7. Remove the polystyrene protection from the bottom. 8. Pull up the appliance in vertical position. 9. Remove the power supply cable and the drain hose from the hose holders. 10. Remove the three bolts. Use the key supplied with the appliance. 11. Pull out the plastic spacers. ENGLISH 31 12. Replace the plastic spacers with the plastic caps. You can find these caps in the user manual bag. WARNING! We recommend that you keep Remove all the packaging and the packaging and the transit the transit bolts before you in-bolts for when you move the ap stall the appliance. pliance. POSITIONING AND LEVELLING x4 • Install the appliance on a flat hard floor. • Make sure that carpets do not stop the air circulation below the appliance. • Make sure that the appliance does not touch the wall or other units • Loosen or tighten the feet to adjust the level. A correct adjustment of the appliance level prevents the vibration, noise and the movement of the appliance when in operation. • The appliance must be level and stable. CAUTION! Make sure that there is sufficient Do not put cardboard, wood or access after the installation for equivalent materials below the possible repairs by a qualified appliance feet to adjust the lev-person. el. Installation on a not hard floor When you install the appliance on a not hard floor (wooden planks floor), put a rigid support plinth under the appliance feet to prevent the noise and the vibration. Assemble the plinth with a waterproof wood panel (min. 15 mm thick) and at- THE INLET HOSE ENGLISH 33 tach it to the beams of the floor with minimum 2 screws. The plinth must extend of some cm more than the edges of the appliance. We recommend you to install the appliance in one of the corners of the room, where the floor is more stable. 35O35O35O45O45O45O • Connect the hose to the appliance. Turn the inlet hose only left or right. Loose the ring nut to set it in the correct position. • Connect the water inlet hose to the cold water tap with 3/4 thread. CAUTION! Make sure that there are no leaks from the couplings. Do not use an extension hose if the inlet hose is too short. Contact the service centre for the replacement of the inlet hose. Water pressure The appliance works correctly if the water pressure is not less than 0.05 MPa (0.5 bar). If you can not connect the water inlet hose to the cold water tap of the primary hydraulic system, connect it to your domestic cold water storage system. Make sure not to have more than a distance of 5.02 m (16.5 ft) between the appliance inlet hose and the bottom of the water storage tank. Water-stop device A The inlet hose has a water stop device. This device prevents water leaks in the hose because of its natural ageing. The red sector in the window «A» shows this fault . If this occur, close the water tap and contact the service centre to replace the hose. WATER DRAINAGE There are different procedures to connect the drain hose: With the plastic hose guide. • On the edge of a sink. • Make sure that the plastic guide cannot move when the appliance drains. Attach the guide to the water tap or the wall. • To a stand pipe with vent-hole. Refer to the illustration. Directly into a drain pipe at a height of not less than 60 cm (23.6”) and not more than 100 cm (39.3”). The end of the drain hose must always be ventilated , i.e. the inner diameter of the drainpipe (min. 38 mm — min. 1.5”) must be larger than the external diameter of the drain hose. 34 ENGLISH 35 • If the end of the drain hose is this (see the drawing), you can push it directly into the stand pipe. Without the plastic hose guide. •To a sink spigot. Refer to the...
Otros modelos de este manual:Lavadoras - L 75270 FL (1.49 mb)
Lavadoras - L 75470 FL (1.49 mb)