Votos - 6, Puntuación media: 3.7
(
)
)
|
Fotos y especificaciones Zanussi FA 722 |
Resumen del manual
Unscrew and remove the three rear screws by means of a key. Hydraulic connection There should be a COLD WATER tap near the washing machine with a screwing on connection pipe of 3/4” gas for the water supply, a sink, a wash basin or a drainage system in the wall. Previously check if: — it is not a hot water tap. — the running water is clean. If not, run off a reasonable amount of water to flush out any debris that may have collected in the pipes. Have the permanent drainage system in the wall checked by a plumber.controlar su buen estado por un fontanero. 2. Lean the appliance back on the rear and fit one of the polystyrene angles between the appliance and the floor. Make sure the hoses are not squashed. A) Place the enclosed rubber joint, delivered in a plastic bag together with the appliance (A) Fig.6), at the very end of the inlet hose and carefully screw the pipe to the tap taking care not to damage the screwdrive and fix the nut well on to the end in order to avoid leaking. 3. Carefully remove the plastic bags on the right and the left, pulling them to the centre of the appliance 4. Place the machine in an upright position and remove the three plastic bolts. 5. Plug the 3 holes with the plastic plugs which you can find in the envelope containing the instruction booklet. B) If necessary turn the hose adequately by unscrewing the nut at the rear of the appliance. C) Now tighten the nut anew to avoid leaks. (Open the tap and asure that it does not leak and close it again.) D) Place the discharging hose in a washbasin or sink with the aid of the bent piece delivered separately. The bent piece has to be entered into the tube’s mouth in order to assure the support. Aforesaid piece allows the hose to be fixed to the wall by means of an opening on the upper part and that way the hose does not move and its falling is avoided. 7 ENGLISH IMPORTANT: The distance from the floor to the highest part of the hose should be between 60 to 90 cm. (It is advised to be between 60 and 70 cm). The hose must not be bent nor twisted to avoid clogging. Should a prolongation of the discharging hose be unavoidable this must never surpass 1.5 m and must be of the same diameter as the original hose. Make sure the hoses are not too tense. Levelling Level the appliance by loosening or tightening the feet. Once in the right position fix the feet by pushing the nuts against the base of the case. Accurate levelling will prevent vibration, noise and displacement of the appliance during operation. Some vibration is inevitable, especially if placed on a wooden floor. Wooden floors are particularly susceptible to vibrations. For advice, consult a builder. If posible always place the appliance on a solid floor. Electrical connections Before plugging the appliance make sure that: 1°. the mains of your installation is the same as on the rating plate of your appliance (the plate is sticked to the rear of the appliance). 2°. The meter, the fuses, the wiring and the socket outlet can support the max. power absorbed stated on the rating plate. 3°. The socket base and the plug must fit in adequately without any reducing interposition, multiple outlets or adapters. If necessary replace the socket outlet by an adequate one. The applicable rules for electrical security require an adequate earthing. The plug of the appliance is provided with such a device. Make sure your socket outlet is provided with an adquate earthing too. The manufacturer declines any liability in case of accidents or incicents should these safety measures not be observed. 8 Your new washing machine This new machine meets all modern requirements for effective treatment of laundry with low water, energy and detergent consumption. • The temperature selector dial will allow you to choose the most suitable temperature for your laundry. • The balance control device ensures the machine is stable during the spin. Description of the appliance 1 Detergent dispenser drawer 2 Programme chart 3 Control panel 4 Door handle 5 Drainage area door 6 Adjustable feet 6 Detergent dispenser drawer ID Prewash UU Main wash ^ Fabric softener, starch 9 ENGLISH Use Control panel 1. Programme chart It will help you to choose the most suitable washing programme for your laundry. 2. RINSE HOLD button O (Easy iron. If you use this button it will be easier to iron the fabrics later). Pressing this button together with the programs for delicate fabrics, the water will hold up in the wash tub at the end of the cycle. Press again to drain the water and take out the clothes. 3. № button Pressing this button before starting the intense program there will be one rinse less which leads to energy and water saving. 4. On/off lamp It lights when the appliance is operating. ® © © 5. Temperature selector™ This control allows you to select the temperature of the washing cycle in accordance with the kind of clothes to be washed. Turn the control until the required te...
Otros modelos de este manual:Lavadoras - FA 822 (823.91 kb)