Votos - 2, Puntuación media: 4
(
)
)
|
Resumen del manual
■ Check that water is coming out of the tap. ■ Check that the inlet hose is not squashed or kinked. ■ Check that the filter in the inlet hose is not blocked. ■ Check that the door is closed. The machine fills then empties immediately: ■ The end of the drain hose is too low. Refer to relevant paragraph in “water drainage” section. The machine does not empty and/or does not spin: ■ Check that the drain hose is not squashed or kinked. ■ The drain filter is blocked. Clean it. ■ The Rinse Hold option has been selected. There is water on the floor: ■ Too much detergent or unsuitable detergent (creates too much foam) has been used. ■ Check whether there are any leaks from one of the inlet hose fittings. It is not always easy to see this as the water runs down the hose; check to see if it is damp. ■ Check that the drain hose is not damaged. ■ Check that the drain filter has been refitted correctly after cleaning. Unsatisfactory washing results: ■ Too little detergent or unsuitable detergent has been used. ■ Stubborn stains have not been treated prior to washing. ■ The correct temperature or programme was not selected. If after all these checks, the problem persists, contact your local Service Force Centre, quoting the model and serial number. This information can be found on the rating plate (see picture). Please note that it will be necessary to provide proof of purchase for any in-guarantee service calls. In-guarantee customers should ensure that the above checks have been made as the engineer will make a charge if the fault is not a mechanical or electrical breakdown. 15 ENGLISH Installation Instructions A It is dangerous to alter the specifications or attempt to modify this product in any way. A Care must be taken to ensure that the appliance does not stand on the electrical supply cable. A Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person. Any plumbing work required to install this appliance should be carried out by a qualified plumber or competent person. A Technical Specifications DIMENSIONS Height 85 cm Width 60 cm Depth 55 cm POWER SUPPLY VOLTAGE 220-230 V / 50 Hz MAX. POWER ABSORBED 2200 W (10 A) WATER PRESSURE Minimum 5 N/cm2 Maximum 80 N/cm2 MAXIMUM RECOMMENDED LOAD Cotton, linen 4.5 kg Synthetics 2 kg Delicate fabrics 2 kg Wool 1 kg SPIN SPEED Maximum FLS 502 500 rpm FLS 602 600 rpm cc This appliance complies with the following E.E.C. Directives: - 73/23 EEC of 19.2.73 (Low Voltage Directive) and subsequent modifications; - 89/336 EEC of 3.5.89 (Electromagnetic Compatibility Directive) and subsequent modifications. 16 Installation Unpacking You are advised to keep all the packaging for re-use in case the appliance has to be transported again. A Before starting the machine up, the transport security bolts must be removed as follows. ■ Unscrew and remove the three rear transit bolts (using a spanner). ■ Lay the machine gently on its back, making sure that the hoses are not squashed. We suggest a polystyrene angle bracket from the packing is placed on the floor before tilting it back to avoid the hoses being squashed. ■ Carefully remove the polyethylene bags located at the base of the machine by pulling them toward the centre of the machine. ■ Place the machine in an upright position and remove the three plastic bolts. ■ Plug the 3 holes with the plastic plugs which you can find in the envelope containing the instruction booklet. 17 ENGLISH Water inlet There should be a COLD WATER tap near the washing machine with a screwing on connection pipe of 3/4 gas for the water supply, a sink, a wash basin or a drainage system in the wall. Previously check if: ■ it is not a hot water tap ■ the running water is clean. If not, run off a reasonable amount of water to flush out any debris that may have collected in the pipes. Have the permanent drainage system in the wall checked by a plumber. Place the enclosed rubber joint, delivered in a plastic bag together with the appliance (A), at the very end of the inlet hose and carefully screw the pipe to the tap taking care not to damage the screwdrive and fix the nut well on to the end in order to avoid leaking. If necessary turn the hose adequately by unscrewing the nut at the rear of the appliance. Now tighten the nut anew to avoid leaks. (Open the tap and assure that it does not leak and close it again.) Water drainage If you intend the drain hose from the machine to empty into a sink, make sure that the sink is empty and that the plug hole is not blocked. Place the drain hose in the sink with the aid of the bent piece delivered separately. The bent piece has to be entered into the tube's mouth in order to assure the support.. Aforesaid piece allows the hose to be fixed to the wall by means of an opening on the upper part and that way the hose does not move and its falling is avoided If the machine is permanently plumbed in, hook ...
Otros modelos de este manual:Lavadoras - FLS 602 (797.23 kb)