Votos - 3, Puntuación media: 4.3 ( )

Fabricar: CDA Tamaño del archivo: 803.39 kb Nombre del archivo: Idioma del manual:

From time to time, depending on the hardness of your water, it is recommendable to run a full wash cycle using a decalcifying product. This will extend the life of your washing machine. The washing machine should be disconnected from the mains electricity supply before any cleaning or maintenance is carried out. 1 CLEANING THE DETERGENT DISPENSER 20 Clean the detergent dispenser whenever there is any washing product residue left inside. a Pull outwards on the detergent dispenser to remove it completely. b Use warm water and a brush to clean the compartments. c Also clean the additive compartment siphons, having removed them first. Once they have been cleaned, put them back making sure that they fit right in to the back. Put the dispenser back into the washing machine. A dirty or incorrectly fitted siphon will prevent the additives from being taken in and leave water inside the compartment at the end of the wash.Important c aa bb CLEANING THE ACCESSIBLE FILTER 2 AND THE OUTSIDE maintenance and cleaning To avoid burns, do not carry out this operation when the wash water is at a temperature of over 30.C. When there have been spillages of detergent or additives from the dispenser onto the washing machine cabinet, clean them up right away as they are corrosive. Clean the accessible filter if the drain pump is blocked by any foreign objects. a Use a coin to turn the filter cap. b Pull out the filter cap. c Place a container under the drain pump filter to collect any water that comes out of it. d Half- or quarter-turn the filter to the left. Water will start to come out. e When all the water has drained out of the washing machine, turn the filter several times until it can be completely removed by gently pulling on it. f Remove the objects or fluff caught in the filter or the drain pump. Put the filter and the filter cap back in place. Important Important CLEANING THE OUTSIDE CLEANING THE FILTER The outside of the washing machine should be cleaned with warm soapy water or a gentle cleaning agent. Do not use abrasive cleaning products or solvents. It should then be thoroughly dried with a soft cloth. 21 washing machine safety and troubleshooting If you detect any problems with Indicaor Problems your washing machine, you will probably be able to rectify them FO1 No water coming in yourself by consulting the following instructions. FO2 Does not drain or spin-dry If this is not the case, unplug the CO3 Does not spin-dry appliance and contact CDA CUSTOMER CARE. FO4 Does not start Important FO5 . Do not open up the . . Call CDA Customer Care washing machine. It does . . not contain any fuses or similar components that F10 can be replaced by the user. This may be due to the following: Check the door is properly shut. Why won’t the washing The washing machine is not plugged into the mains ormachine start? there is no voltage in the mains supply. The Start/Stop button has not been pressed. If the washing machine door is not properly shut, F04 will appear on the display. Why is the washing machine This may be due to the following: vibrating or making too much noise? The blocking and transport screws have not been removed. The washing machine has not been correctly levelled. On spin-drying, the motor makes a kind of whistling noise. This is due to the mechanical action of the motor itself and is perfectly normal. PROBLEMS 22 safety and troubleshooting Why doesn’t the washing machine take in water? Why doesn’t the washing machine drain or spin-dry? Why doesn’t the washing machine spin-dry? Why can’t I see any water in the drum during the wash? If no water is entering, F01 will appear on the display. Indicator F01, no water coming in, this may be due to a cut in the water supply, a tap turned off or a blocked water inlet filter. The possible solutions are as follows: wait for the water supply to be reconnected, turn on the tap, or remove the water inlet hose and clean the filter. If this failure is detected, F02 will appear on the display. The reasons for the F02 indicator may be the following: washing machine drain pump blocked, building drainage pipes blocked, or incorrect pump electrical connection. Solution: if the pump is blocked, gain access to it as described in section 2, maintaining and cleaning the appliance. If this failure is detected, C03 will appear on the display. This may be due to an uneven distribution of clothes in the drum and may cause an excessive level of vibrations. The solution is to select a spin-drying programme. This is due to the fact that the washing machine is provided with a system which is able to adapt to the load and type of fabrics, adjusting the levels of water and energy used, in order to preserve the environment. So, although the water level you can see through the hatch may look low, there is no cause for concern as washing and rinsing efficiency will still be optimum. 23 safety and troubleshooting Why is there still some water in the dispenser? Why can’t I open the hatch immediately aft...

Descargar ahora

Introduzca dos números de la imagen: