Votos - 5, Puntuación media: 3.2
(
)
)
|
Resumen del manual
SAFETY Safety first This instruction manual contains important details on using your machine safely. Please keep it safe for your future reference. If you pass the machine onto someone else, please make sure that you give them this manual so that the new owner can read these safety warnings. . . . Dispose of packaging materials carefully and keep them well away from children. . When disposing of your old machine, to minimise risk of injury to children, isolate from the electrical supply, remove the door, the plug and cut the mains cable off flush with the appliance. Dispose of them separately to make sure that the appliance can no longer be plugged into a mains socket. . This washer dryer is designed for domestic use only. . Before using your machine remove the transit bolts and spacers from the back of the machine. Keep the parts you remove for future transportation. . Any electrical work necessary to install this machine should be carried out by a qualified electrician. . Do not plug your machine into a socket when your hands are wet. . Do not connect the washer dryer to a single outlet instantaneous water heater. . Do not try to modify this machine in any way. . Do not connect the washer dryer directly to an artificial water softening unit. Use the recommended amount of detergent for the water hardness in your area. . Do not let children play with the machine or its controls. . Do not stand on the machine or in the door opening. . Do not lean on the door or use the door to lift or move the machine. . Do not wash or dry garments that have previously been treated with solvents. Remove the polystyrene base... Important check when unpacking your machine: This is part of the polystyrene base and should have stayed intact when you remove the base. If it has broken off and is still in the machine.... to remove it, carefully lay the machine on its side onto the polystyrene top cap and then remove the polystyrene block. Note: You will need a second person to help you lower and raise the machine. INSTALLING MACHINE Installing your machine Follow these steps for trouble free installation: 1. Choose a location... Where you install the machine will affect its performance. . For your safety and to comply with electrical regulations, seek professional advice if you want to install your machine in a bath or shower room. . Make sure that the electrical socket and water taps are easily accessible. You should switch off the machine’s electrical and water supplies when you are not using it. . Make sure that you allow enough space for the machine. Select a space at least 600mm wide, 600mm deep and 850mm high. Also leave enough space to open the door fully so you can load and unload it easily. . Where possible the machine should be positioned on a solid level floor to minimise vibration. . Take care when you move the machine not to rip any floor coverings. There are wheels on the bottom rear of the machine, so tilting it backwards a little is the easiest way to move it. The weight of the machine may cause indentations in some floor coverings. WARNINGS: . Do not plug the machine in and switch it on at the mains until the installation is completed. . You will be charged for a service call if a problem with your machine is caused by incorrect installation or misuse. INSTALLING YOURMACHINE Location of transit bolts. WARNINGS: . Before you use the machine, remove the two transit bolts complete with spacers. If you do not do this, damage may occur to your machine. Keep the parts in case you need them for future transportation. . If and when you replace the bolts complete with spacers make sure you do not overtighten them. 2. Remove the transit fixings... There are two transit bolts fitted under plastic covers, one at either side of the rear of your machine. These bolts prevent damage to the machine while it is being transported. Remove both transit bolts complete with spacers, by following the instructions below. Use a screwdriver to release the covers and a standard 13mm spanner to remove both bolts. Firstly, unhook the grey 3 drainage hose and proceed as follows, taking care not to loosen the hot and cold water fill hoses. 1 2 4 Hold the transit bolt and slide to the side and then pull out. The bolt and spacer should be removed intact. (see below) Example transit bolt complete with spacer. For safety, you must replace the plastic cover over the hole left by the transit bolt. (Repeat steps 1 to 4 to remove the second transit bolt). Using a screwdriver, remove the screw to release the plastic cover. Use a standard 13mm spanner to undo the bolt until three threads can be seen on the bolt. (see below) 3. Connect your machine to the electricity supply Make sure that the electrical socket is accessible. Take the mains lead from the back of the machine and plug it into the socket. We do not recommend wiring your machine directly into the mains supply. Changing the mains lead If you have damaged the existing lead and need a new one, cont...
Otros modelos de este manual:Lavadoras - WD865 (334.69 kb)