Votos - 3, Puntuación media: 3.3
(
)
)
|
Resumen del manual
F232215 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Introduction Model Number Familiarization Guide Sample Model Number: *C125BYVQU60001 *C Model Number Prefix 125 Washer-Extractor Capacity (pounds dry weight of laundry) B Type of Electrical Control Y Actuation (Y = Prep for Card Reader) V Washer-Extractor Speed Capability (V = Variable-Speed) Q Electrical Characteristics U6 Design Series 001 Option Identification (varies from machine to machine) * Denotes Brand *C125BYVQU6001 00000000000 200 – 240 7 3 50 - 60 3 3 125 18 470 N/A N/A 0 500000 EXAMPLE OF NAMEPLATE CHM2012N Figure 2 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F232215 Operation Control Panel Figure 3 shows the control panel. 16 21 5 15 6 14 WASH ADD BLEACH RINSE SPIN DOOR NORMAL QUICK PERM PRESS NORMAL AS QUICK WASH HEAVY SOIL DELICATE RM RESS HOT WARM WARM PHOT HOT WARM COLD COLD START PE W H 7 13 12 8 11 10 9 34 CHM482R 1 Cycle 1 9 START Keypad 2 Cycle 2 10 “Clean Filter” Indicator LED 3 Cycle 3 11 Door Open LED 4 Cycle 4/Up Edit 12 Spin Cycle LED 5 Cycle 5 13 Rinse Cycle LED 6 Cycle 6 14 Add Bleach LED 7 Cycle 7 15 Wash Cycle LED 8 Cycle 8/Down Edit 16 Main LED Display Figure 3 F232215 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Operation Display Indicators Table 1 lists the various displays and what theymean. The operator should become familiar with these machine displays. Display Meaning tESt Diagnostic test cycle selected or enabled SPIn Spin (extract) step SUP1 Supply signal 1 (“S1” output), normally detergent SUP2 Supply signal 2 (“S2” output), normally bleach SUP3 Supply signal 3 (“S3” output), normally softener SUP4 Supply signal 4 (“S4” output) SUP5 Supply signal 5 (“S5” output) SdLY Spin coast (motor coasts after high speed extract) CFIL Cold Fill HFIL Hot Fill bFIL Warm Fill (cold + hot) bLCH Control will also light “add bleach” indicator PASS Variable-speed ONLY – balance “PASS” condition; shows in “test” cycle only FAIL Variable-speed ONLY – balance “FAIL” condition; shows in “test” cycle only bAL? Variable-speed ONLY – meaning: “Do you wish to enter balance detection test routine?” CY__ Cycle number (followed by a space and number 1 through highest cycle number) norn Normal agitation selected gEnt Gentle (reduced) agitation selected SPn1 Variable-speed ONLY – low spin speed (the lower of 2 spin speeds) SPn2 Variable-speed ONLY – high spin speed (the higher of 2 spin speeds) For Wash speed forward (during test cycle) rEv Wash speed reverse (during test cycle) dISt Variable-speed ONLY – distribution speed (during test cycle) LO Low water level nEd Medium water level HI High water level CEL Display all temperatures in degrees Celsius FAr Display all temperatures in degrees Fahrenheit ___C The first 3 digits are reserved for temperature reading, C indicates “degrees Celsius” Table 1 (Continued) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F232215 Operation Table 1 (Continued) Display Meaning ___F The first 3 digits are reserved for temperature reading, F indicates “degrees Fahrenheit” FILL “Fill error” – machine did not fill to programmed water level within 10 minutes dOOr “Door” opened during cycle SHUt/door Machine user must “shut door” of the washer to allow the cycle to begin CAnt/OPEn Control cannot unlock the door CArd Control will interpret the coin 2 input as a START signal from a Card Reader with no timing max restriction, meaning the signal can last any amount of time once recognized USH1 “Wash 1” segment USH2 “Wash 2” segment USH3 “Wash 3” segment USH4 “Wash 4” segment rIn1 “Rinse 1” segment rIn2 “Rinse 2” segment rIn3 “Rinse 3” segment rIn4 “Rinse 4” segment (final rinse) dOnE Cycle has concluded drAI Drain selected for segment; also indicates in drain step during 2 speed version test cycle ---Flashes for a period of time (for safety) after power up while keeping outputs OFF dEn1 Denomination assigned for coin 1 input (example: .25 would mean a US quarter) dEn2 Denomination assigned for coin 2 input (example: 100 would mean a US dollar) Table 1 F232215 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Operation Operating Instructions 1. Turn on main power at its source (circuit breaker). 2. Use left hand to press and hold door unlock button located on top left of door lock box. Refer to Figure 4. 3. Turn handle counterclockwise to open. Refer to Figure 4. CHM2013N Figure 4 4. Load to capacity whenever possible. DO NOT OVERLOAD. Refer to Figure 5. NOTE: Underloading can cause out-of-balance conditions that can shorten machine life. U003I Figure 5 5. Close door and turn handle clockwise to horizontal position. Refer to Figure 6. CHM2014N Figure 6 6. The default wash cycle will display. Refer to Figure 7. NOTE: Perm Press Cold is the default cycle if none is selected. WARNING To avoid personal injury, recommended inlet water temperature should be no higher than 125° Fahrenheit (51° Celsius). W709 CHM482R WASH ADD...
Otros modelos de este manual:Lavadoras - HC125BYV (753.6 kb)