Votos - 2, Puntuación media: 5
(
)
)
|
Resumen del manual
Step 3: Determine Control Type and Temperature Setting Refer to the various controls, pages 9 - 13, follow instructions for the appropriate control type. The type of fabric being dried will determine the temperature setting. Consult the fabric care label or fabric manufacturer to determine proper temperature setting. IMPORTANT: Always follow the fabric care instructions supplied by the garment manufacturer. Step 4: Remove Laundry When the cycle is complete, open door and remove the laundry. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Operation Control Instructions TMB804N REVERSING MODELS Figure 3 Manual Timer Control RT Control Suffix 1. Set the HEAT/DRYING timer for the number of minutes (from 0-60) desired. 2. Set the COOL DOWN/COOLING timer for the number of minutes (from 0-15) desired. 3. Set the TEMPERATURE selector at HIGH, MEDIUM, LOW or anywhere between these settings. 4. Select reversing or nonreversing cylinder rotation setting, if applicable. 5. Press the PUSH TO START button in and hold it in for approximately three seconds. This starts the tumbler cycle. IMPORTANT: If the loading door or lint panel door is opened during the cycle, the heating system will shut off and the motor will stop. To restart the cycle, door must be closed and the PUSH TO START button must be pressed in. 6. When the cycle is complete, open door and remove the laundry. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Operation T359I STATUS DRYING COOL DOWN DOOR OPEN CUSTOM HIGH MEDIUM MED LOW LOW NO HEAT TEMP DISPLAY SIGNAL F/ C TEMP PROGRAM AUTO SPECIAL CYCLE MORE CONDITION SPECIAL TIME COOL DOWN LESS SAVE CUSTOM TIME * + -- * PROG AUTO AUTO ON / SELECT START STOP/RESET REVERSING Figure 4 Electronic OPL Control RM Control Suffix 1. To use an Automatic Cycle, press an ON/ SELECT pad. Select HIGH, MEDIUM, MED LOW, LOW or NO HEAT for items that should not be dried with heat. A light to the left of the selected pad lights up. To use a Time Dry or Custom Cycle, refer to the Programming Manual. NOTE: Do not press directly on lights or the center of pad. For proper selection, press on pad slightly to the right of center. Refer to Figure 5. TMB806N Figure 5 2. Select reversing or nonreversing cylinder rotation setting, if applicable. 3. Press START pad to start tumbler. NOTE: All pads can be pressed in any sequence without damaging control or tumbler. To stop the tumbler at any time, open the door or press STOP/ RESET. The window display will flash. Press STOP/RESET twice (within 3 seconds) to end the cycle and reset the control to idle status. To restart the tumbler, CLOSE door and press START pad. IMPORTANT: If the loading door or lint panel door is opened during the cycle, the heating system will shut off and the motor will stop. To restart the cycle, both doors must be closed and the START pad must be pressed. 4. When the cycle is complete, open door and remove the laundry. NOTE: This machine includes an anti-wrinkle/ extended tumble feature. After the drying cycle is complete, the cylinder will tumble without heat every few minutes. The intermittent tumbling will continue for one hour or until the door is opened. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Reversing Operation Tumblers with the reversing option prevent the tangling of large pieces of laundry and minimize wrinkling. These tumblers are equipped with a second motor and additional controls which reverse the rotation direction of the cylinder. Reverse Control Switch An “on-off” switch for manual timer models, or a touch pad for OPL Micro models is placed in the control panel area so the operator can select the reversing or nonreversing operation. In nonreversing mode, the cylinder will always turn clockwise (as viewed from the front of the tumbler). If the cylinder is turning counterclockwise when switched to nonreversing, it will continue for a few seconds and then start up in the proper direction. Operation IMPORTANT: After any electrical maintenance is done, make sure that the blower motor is turning counterclockwise. Then set the reverse control switch to “nonreversing” and note that the cylinder turns constantly clockwise as viewed from the front of the tumbler. If not, interchange L1 and L2 service leads to reverse the drive motor. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 70283501 11 Operation TMB2136N Figure 6 Dual Digital Timer Control RQ Control Suffix 1. Select HIGH, MED, LOW or NO HEAT by turning the temperature knob. 2. Set the HEAT TIME for the number of minutes (from 0-60) desired. 3. Set the COOL DOWN TIME for the number of minutes (from 0-15) desired. 4. Select reversing or nonreversing cylinder rotation setting, if applicable. 5. Press and release START button to start tumbler. Display will show minutes remaining before end of cycle. NOTE: One touch drying is available for repetitive loads. If the START button is pressed while the machine is in Idle Mode...
Otros modelos de este manual:Lavadoras - 120 Pound Capacity (591.32 kb)