Votos - 0, Puntuación media: 0
(
)
)
|
Resumen del manual
6. Open the service flap 7. Carefully unscrew the pump cover (residual water). 8. Clean the interior, pump cover thread and pump housing (the impeller in the detergent solution pump must rotate). 9. Replace the pump cover and screw it on tightly. 10. Replace the service flap. To prevent unused detergent from flowing straight into the drain during the next wash: Pour 1 litre of water into compartment II and start the Empty .. programme. Drainage hose at the siphon is blocked Turn the programme selector to Off and disconnect the mains plug. 1. Loosen the hose clamp and carefully remove the drainage hose (caution: residual water). 2. Clean the drainage hose and siphon connecting piece. 3. Reattach the drainage hose and secure the connection with the hose clamp. Filter in the water inlet is blocked Risk of electric shock Do not immerse the Aqua-Stop safety device in water (it contains an electric valve). Reduce the water pressure in the supply hose: 1. Turn off the tap. 2. Select any programme (except for Spin ..../ Empty ..). 3. Press Start/Pause ... Let the programme run for approximately 40 seconds. 4. Turn the programme selector to Off. Disconnect the mains plug. Clean the filter: 5. Disconnect the hose from the tap. Clean the filter with a small brush. and/or on standard and Aqua-Secure models: Remove the hose from the rear of the appliance, Take out the filter with a pair of pliers and clean it. 6. Connect the hose and check for leaks. Risk of scalding . Allow the detergent solution to cool down. . Turn off the tap. . Risk of electric shock. Disconnect the mains plug. . Risk of explosion. No solvents. 11 What to do if... .. Water is leaking out. . Attach/replace the drainage hose correctly. . Tighten the screw connection of the supply hose. .. No water supply. Detergent not dispensed. . Start/Pause .. not selected? . Tap not turned on? . Filter blocked? Clean the filter .. page 11. . Supply hose kinked or trapped? .. Washing machine door cannot be opened. . Safety function active. Programme stopped? .. page 4. . - - - - (Rinse stop = no final spin) selected? .. page 3,4. .. Programme does not start. . Start/Pause .. or Ready in time selected? . Washing machine door closed? . Childproof lock active? Deactivating .. page 5. .. Detergent solution is not drained. . - - - - (Rinse stop = no final spin) selected? .. page 3, 4. . Clean the detergent solution pump .. page 11. . Clean the waste pipe and/or drainage hose. .. Water not visible in the drum. . Not a fault - water below the visible area. .. Spin result not satisfactory. Laundry wet/too damp. . Not a fault - the imbalance monitoring system has interrupted the spin because the laundry is unevenly distributed. Distribute large and small items of laundry evenly in the drum. . Speed selected too low? .. page 5. .. The programme duration changes during the wash cycle. . Not a fault - the programme cycle is optimised for the particular washing process. This can cause changes in the programme duration on the display panel. .. Spin cycle performed several times. . Not a fault - unbalanced-load detection system is adjusting the imbalance. .. Residual water in the .. compartment for care products. . Not a fault - the action of the care product is not affected. . Clean the insert if necessary .. page 10. .. Odour formation in the washing machine. . Run programme .. Cottons 90 °C without laundry. Use standard detergent. .. Status display .. flashing. Appliance has detected a detergent overload. . Too much detergent used? Mix one tablespoonful of fabric softener with . litre water and pour into compartment II (Not for outdoor fabrics, sportswear fabrics or those made with down.) . Reduce the detergent dosage for the next wash cycle. .. Loud noises, vibrations and .wandering. during the spin cycle. . Are the appliance feet fixed? Secure appliance feet .. Installation instructions. . Transportation safety devices removed? Remove transportation safety devices .. Installation instructions. .. Display panel/indicator lamps do not function during operation. . Power cut? . Circuit breakers tripped? Switch the circuit breakers back on or replace. . If the fault occurs repeatedly, call the after-sales service. .. Programme sequence longer than usual. . Not a fault - unbalanced-load detection system is adjusting the imbalance by repeatedly redistributing the laundry. . Not a fault - foam detection system active - adds an additional rinse cycle. .. There are detergent residues on the laundry. . Occasionally, phosphate-free detergents contain water-insoluble residues. . Select Rinse .. or brush down the laundry after washing. If you cannot correct a fault yourself (switching on/off) or a repair is required: . Turn the programme selector to Off and remove the mains plug from the socket. . Turn off the water supply and call the after-sales service .. Installation instructions. Washing machine en Instruction manual 1 2 ........ - .... Temp. °C Select the temperature (........ = co...
Otros modelos de este manual:Lavadoras - WAB16260ME/02 (2.19 mb)
Lavadoras - WAB16260ME/04 (2.19 mb)