Votos - 0, Puntuación media: 0
(
)
)
|
Resumen del manual
.. Page 12 Other displays Switch off the appliance, wait 5 seconds and switch on again. If the display appears again, call customer service. .. Page 13 – Risk of electric shock. Pull out the mains plug. – Risk of explosion. No solvents. 11 Risk of scalding. – Allow detergent solution to cool down. Maintenance – Turn off the tap. Drain pump blocked Set the programme selector to .. Off, pull out the mains plug. 1. Open the service flap. 2. Take the drainage hose out of the holder. 3. Remove sealing cap, allow the detergent solution to flow out. Have a suitable container ready. Insert the sealing cap and place the drainage hose back in its holder. 4. Carefully unscrew the pump cover (Caution! residual water). Clean the interior, the pump cover thread and the pump housing (the fan impeller in the detergent-solution pump must rotate). 5. Reinsert and screw on the pump cover. Handle should be vertical. 6. Close the service flap. To prevent unused detergent from flowing into the outlet during the next wash: Pour 1 litre of water into dispenser II and start the .. Spin/Empty .. programme. Drainage hose on the siphon blocked Set the programme selector to .. Off, pull out the mains plug. 1. Loosen hose clip, carefully remove drainage hose (Caution! residual water). 2. Clean the drainage hose and siphon spigot. 3. Re-attach drainage hose and secure connection point with hose clip. Filter in the water inlet hose blocked Risk of electric shock. Do not immerse the Aqua-Stop safety device in water (contains an electric valve). Release the water pressure in the supply hose: 1. Turn off the tap. 2. Select any programme (except .. Rinse/.. Spin/Empty ..). 3. Press the .. Start/Reload button. Leave programme running for approx. 40 seconds. 4. Set the programme selector to .. Off. Pull out the mains plug. Clean the filter: 5. Disconnect the hose from the water tap. Clean the filter with a small brush. and/or for standard and Aqua-Secure models: remove the hose from the rear of the appliance. Take out the filter with pliers and clean. 6. Connect the hose and check for leaks. If you cannot rectify the fault yourself (What to do if our customer service. We will always find a suitable by technicians. You can find the contact data for your nearest service list (depending on the model). Please give customer service the product number of the appliance. Product number Production number open appliance. * Rely on the competence of the manufacturer. Contact You can therefore be sure that the repair is carried genuine spare parts. If you cannot rectify the fault yourself (What to do if our customer service. We will always find a suitable by technicians. You can find the contact data for your nearest service list (depending on the model). Please give customer service the product number of the appliance. Product number Production number open appliance. * Rely on the competence of the manufacturer. Contact You can therefore be sure that the repair is carried genuine spare parts. What to do if … . . . . . . . . . . . . . . . Water is running out. – Correctly atta– Tighten screwch/replace the drainage hose. –fitting on the supply hose. Water not flowing in. Detergent not washed in. – Start/Relo– Tap not open? – Filter blocked– Supply hose kad not selected? ? Cleaning the filter a Page 11 inked or jammed? Washing-machine door cannot be opened. – Safety functio– ----(Rinse ha Page 3, 4 – Can be openen active. Stop the programme? a Page 4 old = without final drain/spin) selected? d via the emergency release only? a Page 13 Programme does not start. – Start/Relo– Door closed? ad or Finish-in time selected? Detergent solution is not drained. – ----(Rinse ha Page 3, 4 – Clean the det– Clean the outlold = without final drain/spin) selected? ergent solution pump. a Page 11 et pipe and/or drainage hose. Water not visible in the drum. – Not a fault -water below the visible area. Spin result is not satisfactory, laundry is wet/too damp. – Not a fault – uthe spin cycleDistribute sma– Too low speenbalanced load detection system has stopped , laundry unevenly distributed. ll and large items of laundry in the drum. d selected? a Page 5 The programme duration changes during the wash cycle. – Not a fault – tparticular wasprogramme dhe programme sequence is optimised for the hing process. This may result in changes to the uration in the display field. Spin cycle actuated several times. – Not a fault -uimbalance. nbalanced load detection system adjusts Residual water in the dispenser for care products ... – Not a fault – e– If required, cleffect of the care product not impaired. an the insert. a Page 10 Odour forms in the washing machine. – Run the a Drstandard deteum Clean 90°C programme without laundry. Use rgent. The status symbol t flashes. Foam may be coming out of the detergent drawer. – Too much detMix 1 tablespointo dispenser (Not for outdo– Reduce the dergent used? on of fabric softener with . litre of water and pour I I. or, sports and down-filled text...
Otros modelos de este manual:Lavadoras - WM12P260IN/02 (2.26 mb)