Votos - 0, Puntuación media: 0
(
)
)
|
Resumen del manual
Starching Laundry must not be treated with fabric softener Starching is possible in all washing programmes if liquid starch is used. Add starch to the fabric softener compartment .. in accordance with the manufacturer’s instructions. Dyeing/bleaching Dye in small quantities only. Salt can corrode stainless steel. Observe the dye manufacturer’s instructions. Do not bleach laundry in the washing machine. Outdoor+Waterproof Laundry must not be treated with fabric softener. Special detergents and impregnating agents suitable for machine washing are available in sports shops. Dose according to manufacturer's instructions: 1. Place the special detergent for outdoor clothing in compartment II and 2. Pour impregnating agent (max. 170 ml) into the compartment ... Move the programme selector to Outdoor+Waterproof ... Select temperature. Touch ....Start/Reload. Final treatment of laundry according to manufacturer’s instructions. 10 Care Machine housing, control panel – Wipe with a soft, damp cloth. – Do not use any abrasive cloths, scourers or cleaning agents (stainless steel cleaners). – Immediately remove laundry and cleaning agent residues. – Do not clean the appliance with a water jet. Clean the detergent drawer ... ... if it contains detergent or fabric softener residues. 1. Pull out the drawer up to the stop position, press down the latch on the insert and remove the drawer completely . 2. Remove insert: pull insert upwards with finger. 3. Clean the detergent dispenser and the insert with water and a brush. 4. Refit the insert and secure in place (the cylinder should fit over the guide pin). 5. Insert the detergent drawer. 6. Leave the detergent drawer open so that residual water can evaporate. Drum Leave the washing machine door open after washing so that the drum can dry. Rust stains – use chlorine–free cleaning agent, not steel wool. Descaling No laundry in the machine! This is not necessary if the detergent is dosed correctly. However, if it is necessary, follow the instructions of the descaler manufacturer. Suitable descaling products can be purchased from our website or customer service. ..page 13 Information on the display .. Please close the door immediately because of rising water level. In pause status and are displayed alternately. .. Door is locked due to safety reasons (water level and/or temperature are too high); in pause status, ..and are displayed alternately. If you need to open the door, wait for the temperature to drop or drain the water (e.g. select Spin .. programme). Door cannot be locked/unlocked due to high temperature of the door lock. Wait a moment and try again. .. Flashing (no water supply): Tap turned on? Inlet filter blocked? Clean filter. ....page 11 Supply hose kinked or blocked? On (low water pressure): Only information. No influence on the programme process. The programme duration will be prolonged. Clean drain pump; ..page 11 outlet pipe/drainage hose blocked. other displays Switch off the appliance, wait 5 seconds and switch it back on. If the display appears again, call the customer service ..page 13 – Risk of electric shock! Pull out the mains plug! – Risk of explosion! No solvents! 11 Maintenance Drain pump – Set the programme selector to .. Off, disconnect the mains plug. 1. Open and remove the service flap. 2. Release the drainage hose from the clip. Remove the sealing plug from the drainage hose, allow the detergent solution to flow out. Push the sealing cap back in. 3. Remove the pump cap. Remove foreign objects/loose debris/fluff from inside and clean the pump. (impeller in the pump must be able to rotate). 4. Clean any residual lye or fluff from the thread of the pump cap and pump housing. 5. Attach the pump cap and screw it on tight until the stop, handle is upright. Place the drainage hose back in the retainer. 6. Place the service flap back on and close. To prevent unused detergent from flowing straight into the drain during the next wash cycle: pour 1 litre of water into compartment II and start the Spin .. programme. Then select and start a new washing programme with detergent as usual. Filter in the water inlet hose Reduce the water pressure in the supply hose: 1. Turn off the tap. 2. Select any programme (except Spin .. or Empty ..). 3. Touch ....Start/Reload button and allow the programme to run for approx. 40 seconds. 4. Set the programme selector to .. Off. Disconnect the mains plug. Clean the filter: 1. Depending on model: Remove the supply hose from the tap. Clean the filter with a small brush. and/or on standard and Aqua-Secure models: Remove the hose from the rear, remove the filter using pliers and clean the filter. 2. Reconnect the supply hose and check if it is tight. – Risk of scalding! Allow detergent solution to cool down! – Turn off the tap! 12 What to do if ... .. Water is leaking out. – Fit/refit drainage hose correctly. – Tighten the screw connection of the supply hose. .. No water supply. Detergent not dispensed. – ....Start/Reload not select...
Otros modelos de este manual:Lavadoras - WS12M460BY/02 (2.07 mb)
Lavadoras - WS12M460BY/03 (2.07 mb)