Votos - 3, Puntuación media: 4
(
)
)
|
Resumen del manual
Do not store pressure washer inside buildings occupied by humans or pets. ce_9o R_ 0 wls/ce 4-ENG The powerful spray from your pressure washer is capable of causing damage to fragile surfaces such as: wood, glass, automobile paint, auto stripping and trim, and delicate objects such as flowers and shrubs. Before spraying, check the item to be cleaned to assure yourself that it is robust enough to resist damage from the force of the spray. Avoid the use of the concentrated spray stream except for very strong surfaces like concrete and steel. Operating unit with water supply shut off without flow of water will result in equipment damage. You should never run this pressure washer for more than 2 minutes without pulling the trigger to allow cool water to enter the pump and the heated (recirculated) water to exiL Running the pressure washer with water supply shut off will void your warranty. Symbols Owner's Manual _'I_ Fuel _Fuel I*'tkI Choke '°"°='°°" ooo. .,o0 Carton Contents • Main Unit pressure washer with wheels • Handle • High Pressure Hose Main Unit Pressure Washer Handle High Pressure Hose with Wheels Bag Containing • Chemical/Soap Hose and Filter • Gun. © • Wand Chemical/Soap Hose and Filter Gun and Wand Bag Containing • Video Cassette • Owner's Manual • Nozzle Cleaning Kit Video Cassette Owner's Manual Nozzle Cleaning Tool • 2 mmAIlen Wrench • 5 mm Allen Wrench • Replacement O-Rings O0 • Engine Oil 2 rnm Alien Wrench 5 mm Allen Wrench Replacement O-Rings • Rubber Isolator and Mounting Hardware • Handle Mounting Hardware I Engine Oil Rubber Isolator and Mounting Hardware Handle Mounting Hardware 5 ENG Tools Required for Assembly Adjustable wrench 5 mm Allen wrench (supplied) Remove Pressure Washer from Carton • Open carton from the top. Locate and remove from box the handle, gun, wand,chemical/soap hose, and parts bag. • Cut carton along dotted lines. • Remove all carton inserts. • Roll unit through opening in carton. NOTE: The hose is located at the bottom of the box. Preparing the Pressure Washer for First Use Note: Included with your pressure washer is a video cassette tape on how to prepare your unit for operation. It is recommended you view this tape before performing the next steps. 1. insert handle onto frame. • Insert knobs into the threaded slot in front of the frame handle and tighten by turning in a clockwise direction. Slide bolts into the slot in the side of the frame handle and tighten the nuts by turning in a clockwise direction. y. / Insert bolt and nlock nut. Tighten knob in clockwise direction. 2. Using an adjustable wrench, remove nut from bolt that attaches board to frame. Remove wood plank from the frame of the unit. Discard bolt and board. 3, Mount the rubber isolator to the frame. To mount isolator place threaded end of bolt through the washer. • Next with washer on bolt place threaded end of bolt through the larger hole in bottom of the rubber isolator• • Place threaded portion of bolt through the same hole location the wood plank was mounted to on the pressure washer. • Next place the tee nut over the threaded portion of the bolt and use the 5 mm Allen wrench provided to tighten isolator to the frame• TEE=:_NUT PRESSUREWASHIER _ --ISOI&TOR FRAME BOLT "_%ASHE R 4. Connect wand extension to gun. TO tighten, turn knob in c_ockwise direction• Hand tighten. 5. Remove tie wrap off of high pressure hose. Unwind high pressure hose and attach the threaded end to the gun. Tighten with adjustable wrench. 6. Connect pressure high pressure hose to outlet on washer and hand tighten firmly. HIGH HOSE NOTE: Always keep hose away from engine muffler. o2e_ge_ Q 3ns/c_ 6-ENG 7, Place assembled washer holder. Gun/Wand Holder gun and wand on pressure , Place pull cord into the wire bracket holder. ,, Pull the cord under the wire bracket to the right of the wire loop. • Lift the pull cord handle up and slide the cord to the left, sliding the cord into the wire loop. • Next slide handle behind the left of the wire loop. the wire bracket to Bracket • Engine recoil will pull the cord into its final position. Checklist Before going any further please review the following: • Be sure you have completed tions. assembly instruc• Double check all fittings to be sure they are tight. IMPORTANT: Before any attempt pressure washer be sure to check Engine Oil on page 8.) to start your engine oil (See Know Your High Pressure Washer Read this Owner's Manual and Safety Rules before operation of your High Pressure Washer Compare this illustration with our pressure washer to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. PUMP-Develops high pressure. ENGINE RUN/STOP SWITCH-Sets engine in starting mode for recoil starter --Stops running engine. RECOIL STARTER-Used for starting the engine manually. SPRAY GUN ASSEMBLY (Contains Gun and Wand)Controls the application of water onto cleaning surface with trigger device. OIL FILL-Port where engine oil is poured,...