Votos - 0, Puntuación media: 0
(
)
)
|
Resumen del manual
.Step1 : Check rubber seal inlet hose .Step2 : Connect hose to water tap Hose connector Hose connector Rubber seal Rubber seal • Two rubber seals are supplied with the water inlet hoses. They are used for preventing water leaks. Make sure the connection to taps is sufficiently tight. Type-A : Connecting Screw-type hose to tap with thread • Screw the hose connector onto water supply tap. Type-B : Connecting Screw-type hose to tap without thread Upper connector Rubber packing Plate Water supply hose Fixing screw 1. Unscrew the adapter ring plate and the 4 adapter retaining screws. 2. Push the adapter onto the end of the tap so that the rubber seal forms a watertight connection. Tighten the adapter ring plate and the 4 screws. 3. Push the water supply hose vertically upwards so that the rubber packing within the hose can adhere completely to the tap and then tighten it by screwing it to the right. 11 Installation Type-C : Connecting one touch type hose to tap without thread Ring plate Guide plate Latch plate 1. Unscrew the adapter ring plate and the 4 adapter retaining screws. 2. Remove the guide plate if the tap is too large to fit the adapter. 3. Push the adapter onto the end of the tap so that the rubber seal forms a watertight connection. Tighten the adapter ring plate and the 4 screws. 4. Pull the connector latch plate down, push the inlet hose onto the adapter, and release the connector latch plate. Make sure the adapter locks into place. NOTE • After connecting inlet hose to water tap, turn on the water tap to flush out foreign substances (dirt, sand or sawdust) in the water lines. Let water drain into a bucket, and check the water temperature. .Step3: Connect hose to washer • Make sure that there are no kinks in the hose and that they are not crushed. .When your washer has two valves. • The Inlet hose which has red connector is for the hot water tap. • If the washer has two valves, the energy is saved by using hot valve. 12 Please use the horizontal tap Horizontal tap Extension tap Square tap NOTE • After completing connection, if water leaks from the hose, repeat the same steps. Use the most conventional type of faucet for water supply. In case the faucet is square or too big, remove the spacing ring before inserting the faucet into the adaptor. Installation • Installation of drain hose about 100 cm about 145 cm about 105 cmmax. 100 cm Hose Retainer Tie strap Laundry tub max. 100 cm max. 100 cm • The drain hose should not be placed higher than 100 cm above the floor. Water in the washer does not drain or drains slowly. • Securing the drain hose correctly will protect the floor from damage due to water leakage. • If the drain hose is too long, do not force back into the washer. This will cause abnormal noise. • When installing the drain hose to a sink, secure it tightly with string. • Securing the drain hose correctly will protect the floor from damage due to water leakage. 13 Installation Leveling Raise Lower Lock Nut Tighten all 4 locknuts securely 1. Leveling the washing machine properly prevents excessive noise and vibration. Install the appliance on a solid and level floor surface, preferably in a corner of the room. NOTE • Timber or suspended type flooring may contribute to excessive vibration and unbalance. 2. If the floor is uneven, turn the adjustable feet as required. (do not insert pieces of wood etc. under the feet) Make sure that all four feet are stable and resting on the floor and then check that the appliance is perfectly level. (use a spirit level) • Once the washer is level, tighten the lock nuts up towards the base of the washer. All lock nuts must be tightened. • Diagonal Check When pushing down the edges of the washing machine top plate diagonally, the machine should not move up and down at all (Please, check both directions). If machine rocks when pushing the machine top plate diagonally, adjust the feet again. 14 NOTE If the washing machine is installed on a raised platform, it must be securely fastened in order to eliminate the risk of falling off. Installation .Concrete floors • The installation surface must be clean, dry and level. • Install washer on a flat hard floor. .Tile floors (Slippery floors) • Position each foot on the Tread Mate and level the machine to suit. (Cut Tread Mate into 70x70 mm sections and stick the pieces on to the dry tile where machine is to be placed.) • Tread Mate is a self adhesive material used on ladders & steps that prevents slipping. .Wooden floors (Suspended floors) • Wooden floors are particularly susceptible to vibration. • To prevent vibration we recommend you place rubber cups under each foot under washer at least 15mm thick, secured to at least 2 floor beams with screws. • If possible install the washer in one of the corners of the room, where the floor is more stable. • Fit the rubber cups to reduce vibration. • You can obtain the rubber cups (p/no.4620ER4002B) from the LG spares dept. NOTE • Proper placement and leveling of the washer w...