Votos - 4, Puntuación media: 4.3
(
)
)
|
Resumen del manual
8 Unpacking Washer Removing shipping hardware Installing hole plugs NOTE Rubber expansion material on spacers may need time to relax before they can be easily pulled through shipping hole. IMPORTANT Save all shipping bolts and spacers for future use. If the washer is to be transported at a later date, the shipping hardware must be reinstalled to help prevent shipping damage. 5 SPACERS 5 SPACERS 5 P CLAMPS 5 P CLAMPS 7 HOLE PLUGS (IN BAG) 1 SHIPPING FORK 1 SHIPPING FORK Remove all of the following: Locate 7 hole plugs in the small bag supplied with washer instruction guides. Insert them in the holes in washer back panel. UNIVERSAL WRENCH (SUPPLIED) 5 BOLTS 5 BOLTS Installation Instructions Leveling your washer Excessive noise and vibration can be prevented by properly leveling the washer. 1. For free standing installation and with the washer within 4 feet (1 m) of its final location, place a level on top of the washer. 2. Use the universal wrench to adjust the leveling legs so the washer is level front-to-rear and side-to-side, and stable corner-to-corner. 3. Press down on alternate corners and sides and feel for the slightest movement. Adjust the appropriate leg(s) so the washer sits solidly on the floor on ALL four legs. Keep the leveling leg extension at a minimum for best performance of the washer. NOTE For pedestal installations, see additional lower installation instructions included with the pedestal. raise 9 10 Installation Instructions Connecting inlet water 1. Run some water from the hot and cold faucets to flush the water lines and remove particles that might clog the water valve screens and to determine which faucet is hot and which is cold supply. 2. Look in the end of each water supply inlet hose and verify that the rubber washers are in place. RUBBER WASHERS MUST BE PRESENT NOTE HOT and COLD water inlet hoses are color coded for identification. The HOT inlet hose is marked with a RED band and the COLD inlet hose is marked with a BLUE band. 3. Connect the HOT inlet hose to the HOT water supply and the COLD inlet hose to the COLD water supply. Tighten by hand until snug. 4. Tighten each supply connection another 2/3 turn with pliers. 5. Turn on the water and check for leaks. 11 3-prong grounded plug CABLE TIE 11 3-prong grounded plug CABLE TIE Installation Instructions Connecting drain and electrical 1. Snap one end of the drain hose hanger (shipped in washer drum) onto the drain hose. Continue wrapping it around the hanger and snap it in place. 2. Place the hook end of the drain hose in the drain opening. Secure the drain hose with the cable tie (provided in the enclosure package) to the standpipe, inlet hose, laundry tub, etc. so the hose does not pull out from the force of the water. IMPORTANT Check to ensure the power is off at a circuit breaker/fuse box before plugging the power cord into an outlet. 3. Plug the power cord into a grounded outlet. Grounding type wall receptacle Power cord with Do not, under any circumstances, cut, remove, or bypass the grounding prong. 4. Turn on the power at a circuit breaker/fuse box. 5. Carefully slide the washer to its final position. Recheck for level and rock corners for stability. Remove and discard door tape. 6. Read the Use & Care Guide provided with the washer. It contains valuable and helpful information that will save you time and money. 7. See the next page about performing a brief, helpful “Installation Cycle” on your new washer. 8. If you have any questions during initial operation, please review the “Service Prevention Checklist” in your Use & Care Guide before calling for service. 9. Place these instructions in a location near the washer for future reference. NOTE A wiring diagram and technical data sheet are located under the washer top panel, on top of the detergent dispenser housing. 12 Installation Instructions Performing Installation Cycle If your washer has this console: 1.Empty washer’s drum and close door. 2.After you plug in the washer the first time: wake up the washer by pressing any button, rotate cycle knob to hand wash cycle, press the start button and then the cancel button. 3.Wake up the washer again by pressing any button, then immediately and simultaneously press and hold both the eco friendly and my favorite buttons for 5 seconds, or until the LCD display changes. 4.The LCD window will display INSTAL CYCLE and show estimated time of cycle completion. Press the start button. The Installation Cycle will automatically test for if water has been turned on. At cycle completion, the LCD window may display INSTAL PASS!, meaning your new washer is properly installed and ready for use. If it prompts an action such as NO WATER, CHECK HOSES or CALL SERVICE 877 435 3287, review the installation steps and make the necessary corrections before you attempt to use the washer. 5.Your washer will exit the Installation Cycle and return to normal operation the next time you wake it up. NOTE Washer will stay awake for 3 minutes after the Instal...