Votos - 3, Puntuación media: 4
(
)
)
|
Resumen del manual
! Read these instructions carefully: they contain vital information on installation, use and safety. Unpacking 1. Unpack the machine. 2. Check whether the washing machine has been damaged during transport. If this is the case, do not install it and contact your retailer. Remove the transit fixings IMPORTANT: Follow these instructions to remove the TWO transit fixings. Situated one either side of the rear panel, BOTH transit bolts MUST be removed before use. ! Failure to do so may cause damage to your machine. It is important the transit bolt and spacer (see pic) come out intact. 1. Unscrew the bolt using a 13mm spanner. 2. STOP when 3 threads can be seen. 3. Hold, slide sideways and pull to remove. 4. For safety, insert one of the plastic covers (supplied with your machine) over the hole. ! Repeat steps 1 to 4 to remove the second transit bolt. ! Packaging materials are not childrens toys. Levelling 1. Install the machine on a flat sturdy floor, without resting it up against walls, cabinets etc. 2. Compensate for any unevenness by tightening or loosening the adjustable front feet. When adjusting the feet, use a spirit level to check the machine stands level, from side to side and from front to back. Levelling your appliance correctly will provide it with stability and avoid any vibrations, noise and shifting during operation. If it is placed on a fitted or loose carpet, adjust the feet in such a way as to allow enough room for ventilation beneath the washing machine. Water connection Connecting the water inlet hose. Remember that this is a cold-fill machine and the fill hose fitted to the rear of the machine must be connected to the cold water supply. Before making the connections to the water outlet, allow the water to run freely from the cold water supply tap until it is perfectly clear. Screw the cold water fill hose onto the cold water supply tap until tight. Turn the tap on and check for leaks: tighten if necessary. ! Make sure there are no kinks or bends in the hose. ! The water pressure at the tap must be within the values indicated in the Technical details table (next page). ! If the water inlet hose is not long enough, contact a specialist store or an authorised serviceman. ! Always use new hoses. ! Check the water hose at least once a year, replace any that are cracked as worn hoses could split under water pressure. 2 Installation Drainage connections A B A. Connect the drain hose, without kinking it, to a draining duct or a wall drain fixed at a height between 65 and 100cm from the floor. B. Alternatively, place it over the edge of a basin, sink or tub, fastening the hose supplied to the tap. The free end of the hose should not be under water. ! We advise against the use of hose extensions. In case of absolute need, the extension must have the same diameter as the original hose and must not exceed 150cm in length. Electrical connections Before plugging the appliance into the mains socket, make sure that: . The socket is earthed and in compliance with the applicable law. . The socket is able to sustain the appliances maximum power load indicated in the Technical Details table (on the right). . The supply voltage is included within the values indicated in the Technical Details table (on the right). . The socket is compatible with the machines plug. If this is not the case, replace the socket or the plug. ! The machine should not be installed in an outdoor environment, not even when the area is sheltered, because it may be very dangerous to leave it exposed to rain and thunderstorms. ! When the machine is installed, the mains socket must be within easy reach and should be connected to a suitable electrical supply. ! Do not use extensions or multiple sockets. ! The power supply cable must never be bent or dangerously compressed. ! The power supply cable must only be replaced by an authorised serviceman. ! The company denies all liability if and when these norms are not respected. The first wash cycle Once the appliance has been installed and before you use it for the first time, run a wash cycle without detergent and no laundry, setting the 90°C programme without a pre-wash cycle. Technical Details Models A1637 A1437 A1237 59.5cm wide Dimensions 85cm high 60cm deep Capacity from 1 to 7kg Wash Electric voltage 220/240 Volts 50Hz connections maximum absorbed power: 1700W-2100W Water maximum pressure 1 MPa (10 bar) connections minimum pressure 0.05 MPa (0.5 bar) drum capacity 54 litres Spin Speed up to 1600 rpm -A1637 up to 1400 rpm -A1437 up to 1200 rpm -A1237 Control programme 3 programmes temperature 60°C according to -run with a 7kg load IEC456 directive This appliance is compliant with the following European Community Directives: - 73/23/EEC & 93/68/EEC (Low Voltage) and subsequent amendments. - 89/336/EEC,92/31/EEC & 93/68/EEC (Electromagnetic Compatibility) and subsequent amendments. GB 3 Washing Machine Description Control panel GB START/STOP Button Programme key LEDs Detergent dispenser TEMPERA...
Otros modelos de este manual:Lavadoras - A1637 (473.24 kb)
Lavadoras - A1237 (473.24 kb)