Votos - 1, Puntuación media: 4
(
)
)
|
Resumen del manual
Do not decompose, repair or alter the machine by yourself. Handicapped or children without care shall not use the machine. Keep the machine away from direct sunlight and heat source like the heater. Do not wash laundries with volatile materials (such as thinner, petrol etc.). Petrol Thinner To protect your laundries and washing machine, please take out all of the coins, buttons, sand, hairpin and other foreign materials before washing. Please check if the water faucet is open, and if the connection of the water inlet pipe is proper. It is suggested to use foamless washing powder. Overflow filter Lint filter <10cm 4 Installation and adjustment Please install and adjust the machine according to the requirement of the manual. It is very important to your security and correct operating the machine. Install the lint filter After opening the package,please take out the lint filter from the document bag,install it to the overflow filter of the wash tub.See to the figure. Usage of the drain hose The drainage shall be smooth with the drain hose. 1.The height of the drain hose shall be less than 10cm , or the drainage willnot be smooth enough and cause incomplete drainage. 2.Do not tramp or press the drain hose. 3.If the drain hose is too long, cut it at mid point. To make smooth drainage, cut the front end of the hose slantingly. Voltage change This washer is assembled for 220V, but can be changed from 220V to 127V. Check your electrical source and follow the diagram below to convert voltage. Blue Green White (1). (2). the safeguard bag to expose the connectors. (4). Detach the white connector from the green one(220V), then inlay it into the blue one(127V). (5). Pack all the connectors with the safeguard bag as usual and f Then install the back cover. Above all the steps must be done by the special serviceman. Please first pull off the power plug and hang up the power cord. Loosen the fastening screw and take off the back cover. (3). Unknit ix it. If you do not need spraying spin, you can fill water into the wash tub directly through this entrance. It can reduce the humidity inside the control panel significantly and prolong the operating life of the components. Quick water-filling entrance Water inlet jointer Quick water-filling entrance Water inlet hose Control handle Push 5 Extend the drain hose from the rear side How to change the direction of the drain hoses Figure 1 indicates the leave factory installation position of the drain hose. Put soft items on the ground. Lean the machine down gently with the front surface facing the ground. Take off the drain hose from the cabinet. Take the hose out of the fixing groove. (See to Figure 2). Embed the drain hose into the groove along the side of the wash tub in the order of (1)~(2), heading for the side of the wash tub. (See to Figure 3). Embed the drain hose into the groove with hands. Take care not to damage the drain hose in fastening the fixing clamp. Figure 1 Figure 2 Figure 3 Figure 4 Embed into the groove in turn Back Extend the drain hose from the side of wash tub Soft item Soft item Extend to the wash tub side Take out the drain hose from the fixing groove. Extend it from the rear side as per the direction of the arrow. (When the drain hose is extended from the rear side, it can be hung on the point for drain hose at the two sides of the cabinet.) (See to Figure 4). Front Install the water inlet hose; Select the water level Adjust the water level adjusting lever to desired water level line. Insert the water inlet hose into the water-filling entrance on the control panel directly. (pull it out to dismantle it) Select water level according to the quantity of the laundries. Attention: In water filling, do not exceed the"High" water level. Otherwise the water may overflow out of the washing machine. Water inlet hose MAX MIN MED Water level indicator Water-filling entrance MED MAX MIN If the extra hose is too long, cut it either at point A or B. > 30mm <1.5m 4.If extra drain hose is needed , please make separate purchase. The inner diameter of the extra hose shall not less than 30mm, and the length shall not exceed 1.5m. A B Preparation before washing Preparation before washing 1.Connect the water inlet hose. 2.Confirm that the washing machine is earthed reliably . Then insert the power plug into the receptacle. Do not connect the earth terminal to the gas pipe and tap water pipe. 3.Put down the drain hose . Pay attention to followings before washing the laundries 4.Slanting or uneven ground may result in unstable working or abnormal noise. Please make the machine stand horizontally. Check if the laundries has special requirement on washing Clear the pocket. Take out the coins, sand, hairpins etc. Tie the long strips; fasten the buttons; close zippers. When the pulsator is running , the buttons of the laundries may cause noise. For the sake of discretion, please put the laundries with buttons into other laundries. The quantity of the laundries shall not be too large...