Votos - 5, Puntuación media: 3.4
(
)
)
|
Resumen del manual
2.Adjust the water level Set the water level with water level adjusting lever according to the laundries quantity. Then fill suitable water continuously. 3.Rinse Adjust the wash timer to 5-7 minutes to do rinsing. OVERFILL If you find water flo- wing out here,please twist the water tap to limit the water filling. 10 Rinse with stored water Rinse with water-filing 1. Put the laundries into the wash tub. Select suitable current according to the laundries. 2. Fill water to preset water level. 3. Rinse Adjust the wash timer to 2-3 minutes to do rinsing. When the laundries quantity is few, please use "Soft" current. If you use "Standard" current, it may splash. Rinsing (Repeat the midway spinning and rinsing with stored water for 2-3 times) 1.Put the laundries into the wash tub. Select suitable current according to the laundries. 2.Adjust the water level Set the water level with water level adjusting lever according to the laundries quantity. Then fill suitable water continuously. 3.Rinse Adjust the wash timer to 5-7 minutes to do rinsing. OVERFILL If you find water flo- wing out here,please twist the water tap to limit the water filling. Spinning Spinning 1. Put the laundries into the spin tub evenly and smoothly. 2. Press the gland in the tub properly. Close the inner and outer cover of the spin tub. 3. Spin Select suitable spin time according to the laundries, and do spinning. During spinning, if there's abnormal sound, it is generally owing to slanting placement of the laundries. Please stop the machine and re-order the laundries. In spinning, it will pause the work if you open the outer cover of the spin tub. Close it to resume the spinning. 11 To do spinning and draining or rinsing with water-filling together, please first do spinning for around 1 minute, then do draining or rinsing with water-filling. Otherwise the spinning will stop owing to too much water stored in the spin tub. Disposal after washing After using, please clean the lint and foreign materials of the lint filter and overflow filter in time. Otherwise it may influence your using the machine. Please first pull off the power plug from the receptacle before cleaning. Cleaning the lint filter 12 Page 4 Cleaning the overflow filter The lint filter must be used during washing. It must be cleaned in time after each using. 1. Press the elastic piece at upper end of lint filter to release the tab from the filter cover 2. Remove lint Pull the lower end of lint filter rear cover outward to disassemble it from the lint filter front cover. Remove lint completely with clear water. (See Figure 2). 3. Install lint filter , and pull the lint filter outward to remove it. (See Figure 1). Figure 1 Figure 2 Lint filter rear cover Lint filter front cover Assemble Disassemble Too much lint on the overflow filter will influence the normal usage of the machine. Please clean it every two months. 1 Take off the overflow filter. As indicated in the figure, nip the elastic fixing claw and pull it to the direction of the arrow to take it off. Elastic fixing claw Cleaning the overflow filter Cleaning the overflow filter 2. Take off the corrugation pipe. Water level Dismantle the upper part of the adjusting lever corrugation pipe inside the overflow filter ( as indicated in Corrugation pipe Figure 1). 3. Cleaning the overflow filter Clean the lint around the filter and flush with tap water. Figure 1 4. Install the overflow filter. (1).Install the corrugation pipe. (2).Insert the mounting plate at Hook the bottom of the filter into the valve cover. (3).Hang up the hook at the left upper side. (4).Push the upper part in as Figure 2 indicated in Figure 2. Disposal of the complete unit Wipe the complete unit with soft cloth twisted dry. Wipe with neutral detergent if too dirty Do not wash it directly by water Thinner Alcohol Petrol After washing, dismount the water inlet hose. Do not store water in the tub for long period. Discharge the water immediately after each using. Pull off the power plug and hang up the power cord. Hang up the drain hose. Wipe off the water drops on the surface and inside the tub with clean soft cloth. Open the cover of the wash tub and the inner/outer cover of the spin tub for some time (about one hour), then close them. 13 Trouble-shooting Answers to question When the remained water is frozen 2~3L Below 50 Prevent the freezing (be sure to discharge the water completely after using) After complete draining, set the "DRAIN SELECTOR" at "OFF" . If it is set at "DRAIN", it will be rather difficult for the frozen water to melt. When the water is frozen Pour hot water below 50 into the wash tub to soak it completely. Then turn the pulsator with hands gently. Please confirm the drainage can work normally before next using. 14 Trouble-shooting Answer to question (If there's breakdown, please pull off the power plug before checking) The following phenomena are not breakdowns sometimes. Please confirm again before sending it to repair. If there are real break...