Votos - , Puntuación media:
(
)
)
Fabricar: Grizzly
Tamaño del archivo: 2.43 mb
Nombre del archivo: 1a881383-e4aa-1af4-75b5-a7356544ff4b.pdf
Idioma del manual:
El documento se está cargando, por favor, espere
 |
El documento se está cargando, por favor, espere
Resumen del manual
3. KEEP WORK AREA CLEAN. 7. DO NOT FORCE TOOL. It will do Cluttered areas and benches invite the job better and safer at the rate accidents. for which it was designed. 4. DO NOT USE IN DANGEROUS 8. USE THE RIGHT TOOL. Do not ENVIRONMENT. Do not use pneuforce tool or attachment to do a job matic tools in damp or wet locafor which it was not designed. tions, or where any flammable or noxious fumes may exist. Keep work area well lighted. 9. DO NOT USE UNDER THE INFLUENCE OF DRUGS OR ALCOHOL. Safety Instructions For Pneumatic Tools 10. USE PROPER AIR HOSE for the 17. DISCONNECT TOOLS before sertool. Make sure your air hose is in vicing, changing accessories, or good condition and is long enough to moving to another location. reach your work without stretching. 18. DO NOT OVERREACH. Keep 11. WEAR PROPER APPAREL. Do not proper footing and balance at all wear loose clothing, gloves, neck-times. ties, rings, bracelets, or other jewelry which may get caught in moving 19. USE THE RECOMMENDED parts. Non-slip footwear is recom- ACCESSORIES. Consult owner’s mended. Wear a protective hair cov manual for recommended acces ering to contain long hair. sories. The use of improper accessories may cause risk of injury. 12. ALWAYS USE ANSI APPROVED SAFETY GLASSES. Also use a 20. CHECK FOR DAMAGED PARTS face or dust mask if cutting operation BEFORE USING. Check for bind- is dusty. Everyday eyeglasses only ing and alignment of parts, broken have impact resistant lenses, they parts, part mounting, loose bolts, are NOT safety glasses. and any other conditions that may affect machine operation. Repair or 13. ALWAYS WEAR ANSI APPROVED replace damaged parts. HEARING PROTECTION. 21. NEVER LEAVE UNATTENDED 14. SECURE WORK. Use clamps or a TOOL CONNECTED TO AIR. vise to hold work when practical. It is Disconnect the air hose and do not safer than using your hand and frees leave tool until it is relieved of any both hands to operate tool. built up pressure. 15. MAINTAIN TOOLS WITH CARE. 22. NEVER ALLOW UNTRAINED Keep tools lubricated and clean USERS TO USE THIS TOOL for best and safest performance. WHILE UNSUPERVISED. Follow instructions for lubricating and changing accessories. 23. IF YOU ARE UNSURE OF THE INTENDED OPERATION, STOP 16. REDUCE THE RISK OF USING THE TOOL. Seek formal UNINTENTIONAL STARTING. Do training or research books or maganot carry tool with hand on trig-zines that specialize in pneumatic ger and always disconnect from air tools. when not in use. H7949/H7950/H7951 Nailer -1 Additional Safety Instructions for Nailers 1. HAND INJURIES: Do not place 5. COMPRESSED AIR RATING: Do your hands near the nail point not connect the nailer to compressed of entry. A nail can deflect and air that exceeds 120 PSI. tear through the surface of the workpiece, puncturing your hand 6. CHECK VALVE: Do not use a check or fingers. valve or any other fitting that allows air to remain in the tool. 2. COMBUSTIBLE GASES: Never connect the nailer to pressur-7. CLEANING: Never use gasoline or ized oxygen or other combustible other flammable liquids to clean the gases as a power source. Only nailer; vapors in the nailer may ignite use filtered, lubricated, and regu-by a spark and cause the nailer to lated compressed air. explode. 3. SAFE HANDLING: Never point 8. OPERATING QUESTIONS: If you the nailer at others! Do not keep are not sure about the intended the trigger pulled when loading operation, stop using the nailer. fasteners, carrying, or holding tool. Seek formal training or research Carry the nailer only by the handle, sources that specialize in pneumatic never by any other part. Do not tools. carry the nailer by the air hose. Disconnect the nailer from the air 9. MAINTENANCE: Always disconnect hose when going up and down air from the nailer when servicing or ladders. installing nails. During adjustments or maintenance, a nailer connected 4. AIR HOSE: Make sure your air to air may fire accidentally, causing hose is designed for the tool in serious personal injury. use, is in good condition, and is long enough to reach your work without stretching. However, an overly long air hose in the work area may be a tripping hazard. -2- H7949/H7950/H7951 Nailer H7949/H7950/H7951 Nailer -3- Operating this nailer can propel objects into the air, causing immediate eye damage. To protect yourself, always wear American National Standards Institute (ANSI) approved safety glasses or goggles when operating this equipment. In addition, the intensity of sound made by this nailer at discharge can reach 90 decibels. To protect your hearing, always wear ANSI approved ear protection when operating this nailer. Never point this nailer at yourself or another person! Always pay attention to the direction this nailer is pointed. Use this tool with respect and caution to lessen the possibility of operator or bystander injury. Ignoring this warning may result in serious personal injury. Nailer accidents routinely happen while moving the gun to another location, such as up ...