Votos - , Puntuación media:
(
)
)
Fabricar: Grizzly
Tamaño del archivo: 749.15 kb
Nombre del archivo: e58d4267-1b53-5884-75bc-fc2457db7ec4.pdf
Idioma del manual:
El documento se está cargando, por favor, espere
 |
El documento se está cargando, por favor, espere
Resumen del manual
Always be sure that the nailer is dry before using it again. Do not allow dust, chips, sand, etc. into the air connectors or into the body of the nailer; this may result in leaks and damage to the nailer and the air couplings. Figure 4. Lubricating nailer via air inlet. G6045/G6046/G6047 18 Gauge Brad Nailer -7 Clearing Jammed Nails The most frequent situation with any type of nailer is a nail jam. A jammed nail must be cleared before using the nailer again. The two places where a nail can get jammed are the magazine and the discharge area. Always disconnect air from nailer whenever clearing a jammed nail! To clear a jammed nail from the magazine: 1. Disconnect the nailer from the air supply! 2. Open the magazine cover and pull the magazine all the way back. 3. Locate and remove the jammed brad nail with a pair of needle nose pliers. Close the magazine cover so it latches. To clear a jammed nail from the discharge area with the Model G6045/G6047: 1. Disconnect the nailer from the air supply! 2. Remove all of the brad nails from the magazine. 3. Flip up the quick release latch that is located on top of the nailer nose assembly as shown in Figure 5. 4. Remove the driver guide cover. 5. The jammed nail should now be visible; remove it from the discharge area with needle nose pliers. -8 6. Replace the driver guide cover and snap the quick release latch back into operating position. Quick Release Latch Driver Guide Cover Figure 5. Removing guide cover. To clear a jammed nail from the discharge area on the Model G6046: 1. Disconnect the nailer from the air supply! Remove all brad nails from the magazine. 2. Loosen the 2 cap screws that secure the driver guide cover to the driver guide on the nose assembly. Slide the driver guide cover toward the nose and pull it over the 2 cap screws. See Figure 6 to identify these parts. 3. The jammed nail should now be visible; remove it with needle nose pliers. 4. Install the guide cover and check the safety yoke mechanism for proper operation (following the same instructions as mentioned in the Safety section). Cap Screws Guide Cover Figure 6. Removing guide cover. G6045/G6046/G6047 18 Gauge Brad Nailer Replacing Pistons/O-Rings If you use your nailer day in and day out, Grizzly offers repair pistons as cheap insurance against wasted down time and lost profits in the event that a piston or piston shaft becomes worn out. To replace a piston: Always disconnect air from nailer whenever servicing! During maintenance, a nailer connected to air may fire accidentally, causing serious personal injury! 1. Disconnect the nailer from the air supply! 2. Remove all nails from the magazine cartridge. 3. Remove the 4 cap screws on the back of the nailer, near the exhaust port. 4. Remove the rear cap as shown in Figure 7. 5. The top of the piston should now be visible inside the cylinder, which is housed in the back of the nailer. Figure 7. Removing rear cap. 6. Remove the guide cover from the nose assembly by loosening the 2 cap screws. 7. Watch the nose assembly and push the top of the piston with your finger. You will see the piston shaft slide along the guide. 8. Push the piston shaft back inside the nailer until you can grip the piston head and remove it from the cylinder. 9. Place a new O-ring on the new piston and apply a thin film of the proper lubricating oil on the O-ring. 10. Insert the new piston in the cylinder. Make sure that the grooves on the piston shaft line up with those on the guide. The new piston should easily slide into the cylinder. Do not force the piston into the cylinder! If the piston is not easily inserted, double- check the alignment of the piston shaft with the grooves on the guide. 11. After the piston is inserted correctly, replace the guide cover and tighten the 2 cap screws. Replace the rear cap assembly and tighten the 4 cap screws. 12. For more assistance, or to install a complete O-ring set, refer to the appropriate breakdown diagram in the back of this manual. G6045/G6046/G6047 18 Gauge Brad Nailer -9 -10- G6045/G6046/G6047 18 Gauge Brad Nailer G6045 PART BREAKDOWN 1 2 3 4 5 7 6 8 9 10 11 12 75 71 72 74 13 14A 18 19A 21 22 19 20 23 24 25 27 26 32 60 62 58 61 63 59 65 64 68 67 66 39 34 36 35 38 37 40A 54 53 55 57 50 47 31 44 43 42 41A 45 48 49 52 51 33 43 46 76 76 8A REF PART # DESCRIPTION REF PART # DESCRIPTION 01 P6045001 CAP SCREW 02 P6045002 LOCK WASHER 03 P6045003 CAP 04 P6045004 SEAL 05 P6045005 SPRING 06 P6045006 O-RING 07 P6045007 CAP SEAL 08 P6045008 PISTON HEAD VALVE 08A P604500A PISTON HEAD ASSY 09 P6045009 O-RING 10 P6045010 STOPPER 11 P6045011 O-RING 12 P6045012 COLLAR 13 P6045013 O-RING 14A P6045014A DRIVER ASSEMBLY 18 P6045018 O-RING 19 P6045019 CYLINDER 19A P6045019A COLLAR 20 P6045020 BUMPER 21 P6045021 O-RING 22 P6045022 O-RING 23 P6045023 BODY 24 P6045024 RETAINING RING 25 P6045025 JOINT GUIDE 26 P6045026 SPRING 27 P6045027 GUIDE SAFETY LVR 31 P6045031 SAFETY YOKE 32 P6045032 STEPPED PIN 33 P6045033 O-RING 34 P6045034 TRGR VALVE HEAD 3...