Votos - 3, Puntuación media: 4.3
(
)
)
|
Resumen del manual
Never carry the tool with finger on trigger, the tool is able to fire a fastener. Tool use and care a. Use clamps or another practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against the body is unstable and can lead to loss of control. b. Do not force the tool. Use the correct tool for the application. The correct tool will do the job better and safer at the rate for which the tool is designed. c. Do not use the tool if the trigger does not turn the tool on or off. Any tool that cannot be controlled with the trigger is dangerous and must not be used until repaired. d. Disconnect the tool from the air source before making adjustments, doing tool maintenance, clearing jams, touching the safety nosepiece, leaving work area, loading, or unloading the tool. Such precautionary measures reduce the risk of injury to persons. e. Store the tool when it is idle out of reach of children and other untrained persons. A tool is dangerous in the hands of untrained users. f. Maintain the tool with care. A properly maintained tool reduces the risk of binding and is easier to control. g. Check for misalignment or binding of moving parts, breakage of parts, and any other condition that affects the tool’s operation. If damaged, have the tool serviced before using. Many accidents are caused by poorly maintained tools. There is a risk of bursting if the tool is damaged. h. Use only accessories that are identified by the manufacturer for the specific tool model. Use of an accessory not intended for use with the specific tool model, increases the risk of injury to persons. i. Use only those fasteners listed in the Specifications chart of this manual. Fasteners not identified for use with this tool by the tool manufacturer are able to result in a risk of injury to persons or tool damage when used in this tool. Service a. Tool service must be performed only by qualified repair personnel. b. When servicing a tool, use only identical replacement parts. Use only authorized parts. c. Use only the lubricants supplied with the tool or specified by the manufacturer. Air source a. Never connect to an air source that is capable of exceeding 90 PSI. Over pressurizing the tool may cause bursting, abnormal operation, breakage of the tool or serious injury to persons. Use only clean, dry, regulated compressed air at the rated pressure or within the rated pressure range as marked on the tool. Always verify prior to using the tool that the air source has been adjusted to the rated air pressure or within the rated air-pressure range. b. Never use oxygen, carbon dioxide, combustible gases or any bottled gas as an air source for the tool. Such gases are capable of explosion and serious injury to persons. SAVE THESE INSTRUCTIONS. SPECIFIC SAFETY INSTRUCTIONS 1. Operators and others in work area MUST wear ANSI-approved safety goggles with side shields during use. The employer is responsible to enforce the use of eye protection by the operator and others in the work area. 2. Keep fingers away from trigger when not driving fasteners to avoid accidental firing. 3. Choice of triggering method is important. Check manual for triggering options. 4. Always assume the tool contains fasteners. 5. Do not point the tool toward yourself or anyone whether it contains fasteners or not. 6. Do not actuate the tool unless the tool is placed firmly against the workpiece. 7. Respect the tool as a working implement. 8. No horseplay. This tool is not a toy and can be deadly if misused. 9. Do not load the tool with fasteners when any one of the operating controls, such as the Trigger or Safety Nosepiece, is activated. 10. Do not remove, tamper with, or otherwise cause the tool operating controls to become inoperable. 11. Do not operate the tool if any portion of the tool operating controls is inoperable, disconnected, altered, or not working properly. 12. Disconnect the tool from the air supply when: a. Unattended. b. Performing any maintenance or repair. c. Clearing a jam. d. Moving the tool to a new location. 13. Do not make any modifications to this tool. 14. Refer to the tool maintenance instructions for detailed information on the proper maintenance of the tool. 15. Fire fasteners into an appropriate work surface only. Do not attempt to fire fasteners into surfaces too hard to penetrate. Do not drive fasteners on top of other fasteners, or at too steep of an angle. Fasteners can ricochet causing personal injury. 16. Do not fire fasteners too close to the edge of a workpiece. They may split the workpiece and fly free, causing personal injury. 17. Keep clear of the workpiece near the area being fastened. Fasteners may bend sideways during firing, causing them to exit the workpiece at an unexpected point, causing personal injury. 18. Transport Tool safely. Always disconnect air supply when moving the tool. Carry the tool by the handle and avoid contact with the trigger. 19. Hold tool away from head and body. During operatio...