Votos - 2, Puntuación media: 3.5
(
)
)
|
Resumen del manual
If this occurs, let the cartridge cool off for a while. Then re-insert it and try to charge it once more. 0 When you charge a new battery cartridge or a battery cartridge which has not been used for a long period, it may not accept a full charge. This is a normal condition and does not indicate a problem. You can recharge the battery cartridge fully after discharging it almost completely a couple of times. 0 If you wish to charge two battery cartridges, allow 15 minutes between chargings on the fast charger. Safety system Make sure all safety systems are in working order before operation. The tool must not operate if only the trigger is pulled or if only the safety lever is pressed against the wood. It must work only when both actions are performed. Test for possible faulty operation with a tool unloaded and pointed well away from yourself or any bystanders. NOTE: There is a possibility that the tool may operate for an instant when only the trigger is pulled. This does not indicate a problem. If this occurs, point the tool well away from yourself or any bystanders. Release and pull the trigger again to make sure the safety systems are in working order. Loading staples CAUTION: Always remove the battery cartridge before loading the staples into the tool. Press the plate spring on the rear of the sub-magazine and slide the sub-magazine Plate spring backward. Load staples into the main magazine with staple ends facing up as illustrated at right. To secure the sub-magazine in place, push the sub-magazine while pressing the plate spring on the rear of the sub-magazine. CAUTION : 0 Always secure the sub-magazine in place, or the staples can drop out and cause problems. With the magazine loaded, if the tool is held downward and the sub-magazine is opened, the staples can fall out and present a danger to anyone or anything below. Keep this in mind especially when working in high locations. Depth adjustment hlllf If the staples are driven too deep or too I shallow, adjust the driving depth by turn- I i ing the nut on the bottom of the tool. For deeper driving of staples, turn the nut clockwise. For shallower driving, turn the nut counterclockwise. Please note the nut must be turned in increments of 180" (1/2 turn) so that the groove on the nut runs parallel to the magazine. NOTE : If the distance between the tool end (A) and the material to be fastened is more than 2 mm (5/64"), the tool will not operate because the safety lever is not pressed enough to operate the tool. Driving staples Place the tool on the material to be fastened so that the front and the rear of the tool contact the material flat. Do not tip the tool to the right or left side. Hold the tool firmly against the material, Then pull the trigger to drive the staples. If the staples are driven too shallow, press the tool head as shown in the figure and drive the staples. If the staples are still driven too shallow, adjust the driving depth by turning the nut clockwise. Refer to "Depth adjustment". CAUTION : Do not operate the tool without staples. It shortens the service life of the tool. If the tool becomes jammed, do as follows. First, remove the battery cartridge. Open the sub-magazine and remove the stuck staple using a screwdriver or the like. Sight window There is a convenient sight window on the tool side. Use this sight window to check if there are staples in the magazine. When staples are not visible through the window, load staples into the magazine. Staples 0 Handle the staples and their box carefully. If the staples have been handled roughly, they may be bent out of shape, causing poor staple feed or jamming. .Avoid storing the staples in a very humid or hot place or place exposed to direct sun- light. 0 Do not attempt to use staples that appear to be damaged, bent, rusty or corroded. MAINTENANCE CAUTION : Always remove the battery cartridge before attempting to perform inspection or main- tenance. To maintain product SAFETY and RELIABILITY, repairs, maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts only. ACCESSORIES CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. Staples 5,000 798377-2 I 10 (13/32") I 22 (7/8") I A 1hour fast charger 1hour fast automotive charger Model DC9700 Model DC9112 Part No. 113103-2 Part No. 1131 10-5 Battery cartridge 9100 Plastic carrying case Part No. 192019-4 Part No. 182403-1 Battery cover 15 minute fast charger Part No. 41 4938- 7 Model DC9015 Part No. 113106-6 Jan -21-92 US CORDLESS STAPLER Model T221D Note: The switch and other part configurations may differ from country to country. MODEL T221D Jan.-21--'92 US 'i\M DESCRIPTION 'L5M DESCRIPTION AtD Switch 26 1 Housing Set iWlth Item 451 2...