Votos - 2, Puntuación media: 4 ( )

Fabricar: DeVillbiss Air Power Company Tamaño del archivo: 467.35 kb Nombre del archivo: Idioma del manual:

7 PREPARING THE TOOL NOTE: This tool is shipped completely assembled. No assembly time or tools are required. 1. After reading and understanding this entire manual, connect tool to air supply (Fig. 18). 2. Depress latch and slide magazine core open (Fig. 19). 3. Turn the tool upside down. Insert a strip of fasteners into the magazine channel (A) Fig. 20. With the tool upside down, orient fasteners with points up in the magazine channel (B) Fig. 20. NOTE: Staples are loaded from the bottom. 4. Push magazine core closed (Fig. 21). 5. Observe the low fastener indicator (A) Fig. 22 and reload as needed. 6. Adjust directional exhaust deflector (A) Fig. 23, so that the exhaust air or debris will be directed away from the operator. Grasp the deflector and rotate it to the desired position for the current application. Fig. 18 Fig. 19 Fig. 20 B A Fig. 21 A A Fig. 22 Fig. 23 8 OPERATING INSTRUCTIONS USING THE TOOL Complete all steps of PREPARING THE TOOL before using the tool. This tool is shipped from the factory with a “single sequential actuation” trigger. This actuation design requires the release of both the trigger and safety mechanism after each fastener is driven. Sequential actuation is the only triggering option available for this tool. To fire, grip the tool firmly to maintain control, position nose of tool onto work surface, push the tool firmly against work surface to depress safety (S) Fig. 24, and squeeze trigger to fire a fastener. Allow tool to recoil away from work surface as fastener is driven. This “single sequential actuation” method provides the most accurate fastener placement. Disconnect tool from air supply before performing maintenance, clearing a jammed fastener, leaving work area, moving tool to another location, or handing the tool to another person. Clean and inspect tool daily. Carefully check for proper operation of trigger and safety mechanism. Do Not use the tool unless both the trigger and the safety mechanism are functional, or if the tool is leaking air or needs any other repair. Fig. 24 S RUBBER NOSE CUSHION A rubber nose cushion (A) Fig. 25 is provided to reduce marring of the work surface. The rubber cushion can be removed when it is not required. Disconnect tool from air supply before removing or installing rubber cushion. Fig. 25 A 9 CLEARING A JAMMED FASTENER Disconnect tool from air supply. 1. Open magazine and remove remaining fasteners (Fig. 26 and Fig. 27). NOTE: Remove fasteners from tool before opening the fastener guide plate. Fasteners are under pressure and may shoot out of magazine which could cause injury. 2. Depress the quick release latch and open the fastener guide plate (Fig. 28). 3. Remove the jammed fastener (Fig. 29). 4. Depress the quick release latch and close the fastener guide plate. Fig. 27 Fig. 26 Fig. 29Fig. 28 MAINTENANCE CLEAN AND INSPECT DAILY Disconnect tool from air supply before cleaning and inspection. Correct all problems before placing the tool back in use. Wipe tool clean and inspect for wear or damage. Use non-flammable cleaning solutions to wipe exterior of tool only if necessary. DO NOT SOAK tool with cleaning solutions. Such solutions can damage internal parts. Inspect trigger and safety mechanism to assure system is complete and functional: no loose or missing parts, no binding or sticking parts. Keep all screws tight. Loose screws can cause personal injury or damage tool. If tool is used without an in-line oiler: place 5 or 6 drops of Air Tool Oil into the air inlet of the tool at the beginning of each workday. 10 SERVICE SERVICE AND REPAIRS All quality tools will eventually require servicing or replacement of parts due to wear from normal use. For assistance with your tool, visit our website at for a list of service centers or call the Customer Care Department at 1-800-888-2468. All repairs made by our service centers are fully guaranteed against defective material and workmanship. We cannot guarantee repairs made or attempted by others. Should you have any questions about your tool, feel free to write us at any time. In any communications, please give all information shown on the nameplate of your tool (model number, type, serial number, etc.). TROUBLESHOOTING GUIDE Disconnect tool from air supply before performing any Service Procedure. SYMPTOM PROBLEMS SOLUTIONS 1. Air leak near top of tool or in trigger area. Loose screws. Worn or damaged o-rings or seals. Tighten screws. Install Overhaul Kit. 2. Tool does nothing or operates sluggishly. Inadequate air supply. Inadequate lubrication. Worn or damaged o-rings or seals. Verify adequate air supply. Put 5 or 6 drops of oil into air inlet. Install Overhaul Kit. 3. Air leak near bottom of tool. Loose screws. Worn or damaged o-rings or bumper. Tighten screws. Install Overhaul Kit. 4. Tool jams frequently. Incorrect fasteners. Verify approved fasteners of correct size. Damaged fasteners. Magazine or nose screws loose. Replace w/undamaged fasteners. Tighten screws. Magazine i...

Descargar ahora

Introduzca dos números de la imagen: