Votos - 2, Puntuación media: 5
(
)
)
|
Resumen del manual
The assembly should now be assembled as shown in Figure 8. Figure 6. Sliding table support and rack over the column. Figure 7. Correct column ring orientation. Figure 8. Handles and lock levers installed. SET UP -13 M1102/M1103 16-Speed Drill Press Headstock SET UP The headstock must be mounted on the column/base assembly before the drill press can be operated. Moving and installing the headstock is a two-person job. To install the headstock, do these steps: 1. Loosen the two set screws on the right side of the headstock enough so they are flush with the inside pocket of the headstock. The headstock is very heavy. In the next step, you MUST have assistance when moving, lifting or mounting the headstock on the column and base assembly. NOTICE When doing the next step, DO NOT force the head- stock onto the column! If you do, you could damage the headstock and the column. 2. With the help of an assistant, lift the headstock assembly above the column, and gently slide it down the column as far as it will go. Note: An alternate method is to lay the headstock on the packaging styrofoam and slide the column into the headstock, tilt the assembly up, and position the drill press on its base in the upright position. 3. Place a ruler or tape measure on the base and suspend a plum bob from the center of the headstock spindle so it is over the tape/ruler as shown in Figure 9. 4. Center the headstock directly over the base as indicated by the plum bob and ruler. 5. Tighten the two headstock setscrews to the column, as shown in Figure 10. Figure 9. Aligning headstock with a typical drill press base. Figure 10. Securing headstock to column. -14 M1102/M1103 16-Speed Drill Press Chuck Guard The chuck guard must be installed before the chuck is attached to the spindle. To install the chuck guard, do these steps: 1. Loosen the Phillips head screw and lock nut on the chuck guard clamp. 2. Place the chuck guard over the spindle, and tighten the Phillips head screw and lock nut. Note: (Optional) To prevent the guard from slipping off of the spindle, move the table up until it is just below the guard as shown in Figure 11. Or have an assistant hold the guard in place while you secure it. Figure 11. Installing chuck guard. Drill Chuck & Arbor The drill chuck attaches to the spindle by means of the arbor, shown in Figure 12. Matched tapers on the arbor and the inside of the chuck create a semi-permanent assembly when properly joined. When the drill press is shipped from the factory, a plastic plug is installed in the chuck. To assemble the drill chuck and mount it to the spindle, do these steps: 1. Use the chuck key to back the jaws out and remove the plastic plug. 2. Use mineral spirits to thoroughly clean the drill chuck, arbor, and spindle sockets and dry all surfaces before assembly. Follow all safety warnings on the container of the mineral spirits. Failure to clean the mating surfaces may cause the tapered fit to loosen during operation, resulting in separation and an unsafe condition. 3. Use the chuck key to adjust the jaws of the drill chuck until they are inside the drill chuck body. Figure 12. Chuck components. Drill Chuck Chuck Key Arbor Drift Key -15 SET UP M1102/M1103 16-Speed Drill Press SET UP 4. Place the drill chuck face down on a workbench. The arbor has a short taper and a long taper. Place the short taper into the socket in the back of the drill chuck and tap it with a rubber or wooden mallet, as shown in Figure 13. If the chuck fails to remain secure on the arbor, repeat Steps 1 & 2. 5. Raise the chuck guard. 6. Slide the arbor into the spindle socket while slowly rotating the drill chuck. The socket has a rectangular pocket where the tang (or flat portion of the arbor shown in Figure 13) fits into. 7. Using only a rubber or wooden mallet, tap the chuck and arbor assembly into the quill as shown in Figure 14. DO NOT use a steel hammer. Figure 13. Seating arbor into chuck. DO NOT use a steel hammer on the drill chuck to seat the arbor into the spindle. You will damage the chuck and/or spindle, which may make them unusable or unsafe. Figure 14. Seating arbor and chuck into spindle. -16 M1102/M1103 16-Speed Drill Press Downfeed Handles & Belt Cover Knob The downfeed handles must be installed to properly operate the drill press. To install the downfeed handles, do these steps: 1. Thread the knobs onto the handles, then thread the handles into the spindle hub, as shown in Figure 15, and tighten. 2. Install the belt cover knob in its place (see Figure 15 for location). Table The table must be installed to properly support the workpiece during operation. To install the table, do these steps: 1. Insert the table shaft into the table support assembly. 2. Tighten the small locking lever (Figure 16) to secure the table in the table support assembly. Spindle Hub Belt Cover Knob Figure 15. Downfeed handles and belt cover knob installed. Figure 16. Table installed. SET UP -17 M1102/M1103 16-Speed Drill Press Work Light SET UP...
Otros modelos de este manual:Clavadoras - SHOP FOX M1102 (6.19 mb)