Votos - , Puntuación media:
(
)
)
Fabricar: Porter-Cable
Tamaño del archivo: 238.75 kb
Nombre del archivo: 63eff93c-a784-a044-fd6e-b025147a1cd1.pdf
Idioma del manual:
El documento se está cargando, por favor, espere
 |
El documento se está cargando, por favor, espere
Resumen del manual
If you have any questions relative to its application DO NOT use the tool until you have written Porter- Cable and we have advised you. Technical Service Manager Porter-Cable Corporation 4825 Highway 45 North Jackson, TN 38305 1. USE SAFETY GLASSES. To prevent eye injuries, the tool operator and all persons in the work area must wear safety glasses with permanently attached, rigid, plastic side shields. These safety glasses must conform to ANSI Z87.1 requirements (approved glasses have “Z87” printed or stamped on them). Fig. 1. 2. WEAR EAR PROTECTION to safeguard against possible hearing loss. Fig. 1. 3. OPERATOR AND BYSTANDERS WEAR HARD HAT to safeguard against possible injuries. Fig. 1. 4. USE CLEAN, DRY, REGULATED compressed air at 70 to 120 PSI, (4.8 to 8.3 BAR). Fig. 2. 5. DO NOT CONNECT TOOL to pressure which potentially exceeds 200 PSI (13.7 BAR). 6. ONLY USE AIR HOSE THAT IS RATED for a maximum working pressure of at least 150 PSI (10.3 BAR) or 150% of the maximum system pressure, which ever is greater. 7. NEVER USE OXYGEN, CARBON DIOXIDE, combustible gases or any other bottled gas as a power source for this tool: explosion and serious personal injury could result. Fig. 3. 8. CONNECT TOOL TO AIR SUPPLY HOSE with a coupling that automatically removes all pressure from the tool when the coupling is disconnected. Fig. 4. 3 Fig. 1 Fig. 2 Fig. 3 Fig. 4 903090 - 06-30-01.qxd 9/25/02 1:52 PM Page 4 9. DISCONNECT TOOL FROM AIR SUPPLY HOSE before doing tool maintenance, clearing a jammed fastener, leaving work area, moving tool to another location, handing the tool to another person, or making adjustments. Fig. 4. 10. NEVER USE A TOOL that is leaking air, has missing or damaged parts, or requires repair. Make sure all screws and caps are securely tightened. Fig. 5. Fig. 5 Fig. 6 Fig. 7 Fig. 8 Fig. 9 11. NEVER USE TOOL IF SAFETY, trigger or springs are inoperable, missing or damaged. Do not alter or remove safety, trigger, or springs. Make daily inspections for free movement of trigger and safety mechanism. Fig. 5. 12. DO NOT USE TOOL WITHOUT SAFETY WARNING LABEL. If label is missing, damaged or unreadable, contact your Porter-Cable Service Center for a replacement. Fig. 6. 13. ONLY USE PARTS, FASTENERS, AND ACCESSORIES recommended by Porter- Cable. 14. REMOVE ALL FASTENERS from tool before connecting to air supply. The tool’s driving mechanism may cycle when tool is connected to the air supply. Fig. 7. 15. ALWAYS ASSUME THE TOOL CONTAINS FASTENERS. Keep the tool pointed away from yourself and others at all times. No horseplay. Respect the tool as a working implement. Fig. 8. 16. DO NOT LOAD FASTENERS with trigger or safety depressed, to prevent unintentional firing of a fastener. Fig. 9. 17. REMOVE FINGER FROM TRIGGER when not driving fasteners. Never carry tool with finger on trigger. Tool will fire a fastener if safety is bumped while trigger is depressed. Fig. 10. 18. DON’T OVERREACH. Keep proper footing and balance at all times when using or handling the tool. 4 903090 - 06-30-01.qxd 9/25/02 1:53 PM Page 5 Fig. 10 Fig. 11 19. FIRE FASTENERS INTO WORK SURFACE ONLY, never into materials too hard to penetrate. Fig. 11. 20. GRIP TOOL FIRMLY TO MAINTAIN CONTROL WHILE allowing tool to recoil away from work surface as fastener is driven. If safety element is allowed to recontact work surface before trigger is released an unwanted fastener will be fired. 21. DO NOT DRIVE FASTENERS on top of Fig. 12 Fig. 13A Fig. 13B other fasteners, or with the tool at too steep an angle: the fasteners can ricochet causing personal injury. Fig. 12. 22. DO NOT DRIVE FASTENERS CLOSE to the edge of the workpiece. The workpiece is likely to split allowing the fastener to fly free or ricochet causing personal injury. Fig. 12. 23. KEEP HANDS AND BODY PARTS away from area shown in Fig. 13A, to avoid injury. 24. DO NOT USE ON SCAFFOLDINGS OR LADDERS or for tasks in which changing location involves the use of scaffoldings, stairs, ladders, and the like. Do not use for specific tasks such as closing boxes or crates or fitting transportation safety systems on vehicles and wagons. Fig. 13B. TECHNICAL SPECIFICATIONS Noise level Typical Mean A - Weighted sound impulse effective Acceleration . . .3.91 m/s2 power level . . . . . 95.1 dBA P - Emission sound pressure pressure level . . . 86.3 dBA 5 903090 - 06-30-01.qxd 9/25/02 1:53 PM Page 6 EMPLOYER’S RESPONSIBILITIES WARNING: Employer must enforce compliance with the safety warnings and all other instructions contained in this manual. Keep this manual available for use by all people assigned to use this tool. For personal safety and proper operation of this tool, read and follow all of these instructions carefully. OPERATING INSTRUCTIONS FOREWORD Porter-Cable Model DA250A is a heavy duty pneumatic finish nailer. It is designed to install 15 ga. finish nails of various lengths (from 11/4" to 21/2" long), see ACCESSORIES Listing in back of this manual. CAUTION: Use approved Porter-Cable finish n...