Votos - 3, Puntuación media: 3.7
(
)
)
|
Resumen del manual
Keep hoses away from heat, oil and sharp edges. Replace any hose that is damaged, weak or worn. Personal injury or tool damage could occur. Operating Instructions MXN10300 O CO2 100 psi Latch Magazine Work contact element (WCE) Fastener discharge area Trigger Fastener loading area Tool Components and Specifications Cap exhaust • REQUIRES: 0.8 SCFM with 10 fasteners per minute @ 90 PSI • AIR INLET: 1/4” NPT • STAPLE SIZE RANGE: 3/8” to 1-1/4” • MAGAZINE CAPACITY: 100 Staples per load, 18 gauge • WEIGHT: 2 lb., 15 oz. • LENGTH: 10-1/2” • HEIGHT: 9-1/2” • MAXIMUM PRESSURE: 100 PSI • PRESSURE RANGE: 60 – 100 PSI Nozzle shield Quick clear nose Adjustable depth control (not visible) 6 Operating Instructions MXN10300 Staples Interchange Information MXN10300 can use 3/8” to 1-1/4” 18 gauge 1/4” crown staples designed for the following tools: • Campbell Hausfeld® SN258K • Hitachi® N3804AB • Porter Cable® NS100, NS150 • Senco® SLS15, SLS18, SLS25XP 1 1 MPA bar psi 1 1 7 . . . . 5 9 1 6 8 1 1 3 4 1 Recommended Hookup Quick Plug Quick Coupler Air Hose Quick Plug (Optional) Quick Coupler (Optional) Filter/Regulator 3 General Safety Information (Continued) Always assume the tool contains fasteners. Respect the tool as a working implement; no horseplay. Always keep others at a safe distance from the work area in case of accidental discharge of fasteners. Do not point the tool toward yourself or anyone whether it contains fasteners or not. Accidental triggering of the tool could result in death or serious personal injury. Do not drive a fastener on top of other fasteners. The fastener could glance and cause death or a serious puncture wound. Do not operate or allow anyone else to operate the tool if any warnings or warning labels are not legible. Warnings or warning labels are located on the tool magazine and body. Do not drop or throw the tool. Dropping or throwing the tool can result in damage that will make the tool unusable or unsafe. If the tool has been dropped or thrown, examine the tool closely for bent, cracked or broken parts and air leaks. STOP and repair before using or serious injury could occur. Caution indicates a potentially hazardous situation which, if not avoided, MAY result in minor or moderate injury. ! CAUTION Operating The Stapler RECOMMENDED HOOKUP The illustration below shows the recommended hookup for the tool. 1. The air compressor must be able to maintain a minimum of 60 psi when the tool is being used. An inadequate air supply can cause a loss of power and inconsistent driving. 2. Always use air supply hoses with a minimum working pressure rating equal to or greater than the pressure from the power source if a regulator fails, or 150 psi, whichever is greater. Use 3/8” air hose for runs up to 50’. Use 1/2” air hoses for 50’ run or longer. For better performance, install a 3/8” quick plug (1/4” NPT threads) with an inside diameter of .315” (8mm) on the tool and a 3/8” quick coupler on the air hose. 3. Use a pressure regulator on the compressor, with an operating pressure of 0 - 125 psi. A pressure regulator is required to control the operating pressure of the tool between 60 and 100 psi. Do not make any modifications to the tool without first obtaining written approval from Campbell Hausfeld. Do not use the tool if any shields or guards are removed or altered. Do not use the tool as a hammer. Personal injury or tool damage may occur. Avoid long extended periods of work with the tool. Stop using the tool if you feel pain in hands or arms. Always check that the Work Contact Element (WCE) is operating properly. A fastener could accidentally be driven if the WCE is not working properly. Personal injury may occur (See "Checking the Work Contact Element" Section). Disconnect air supply and release tension from the pusher before attempting to clear jams because fasteners can be ejected from the front of the tool. Personal injury may occur. Notice indicates important information, that if not followed, MAY cause damage to equipment. Avoid using the tool when the magazine is empty. Accelerated wear on the tool may occur. Clean and check all air supply hoses and fittings before connecting the tool to an air supply. Replace any damaged or worn hoses or fittings. Tool performance or durability may be reduced. NOTICE Operating Instructions MXN10300 ! WARNING 60 psi Min. 100 psi Max. 150 psi or greater 3/8” I.D. Operating The Stapler (Continued) ADJUSTING THE DIRECTION OF THE EXHAUST The tool is equipped with an adjustable direction exhaust deflector. This is intended to allow the user to change the direction of the exhaust. Simply twist the deflector to any direction desired. CLEARING A JAM FROM THE TOOL 1. Disconnect the air supply from the tool. 2. Remove all fasteners from the magazine (see Loading/ Unloading). Failure to remove all fasteners will cause the fasteners to eject from the front of the tool. 3. Undo hook by pushing down on the button on the side of the magazine. The button will diseng...