Votos - 3, Puntuación media: 4.7
(
)
)
|
Resumen del manual
When servicing, use only identical replacement parts. Use of any other parts will void the warranty. Only use accessories intended for use with this item. Approved accessories are available from Harbor Freight Tools. 12. Do not assemble this chair if under the influence of alcohol or drugs. Read warning labels on prescriptions to determine if your judgment or reflexes are impaired while taking drugs. If there is any doubt, do not proceed with assembly. 13. Maintenance. For your safety, service and maintenance should be performed regularly. Check the alignment of all parts, and check the tightness of all fasteners. Warning: The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. Unpacking When unpacking, check to make sure the following parts are included. 1 Back 1 Front Support 1 Seat 14 Wood Screws 2 Front Legs 10 55mm Bolts with nut and washer 2 Back Supports 2 65mm Bolts with nut and washer 2 Arms 1 Owner’s Manual If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this manual, or contact your local Harbor Freight retailer. SKU 91090-91091 Page 3 Assembly Assembly 1. Attach Left Front Leg (C1) and Right Front Leg (C2) to Seat (B) using 3 Bolts (H) per side. Use the included washers and nuts to tighten. 2. Attach both Back Supports (D) to the inner sides of the Seat (B) using 2 Bolts (H) per side. Tighten using the included washers and nuts. 3. Attach the Left Arm (E1) and Right Arm (E2) to the Front Legs (C1, C2) using 2 Wood Screws (G) per side. Attach the Arms (E1, E2) to the Back Supports (D) using 1 Long Bolt (I) per side. Tighten the bolts using included washers and nuts. 4. Attach the Back (A) to Seat (B) and Back Supports (D) using a total of 6 Wood Screws (G). 5. Attach the Front Support (F) to the Front Legs (C1, C2) using 2 Wood Screws (G) per side. 6. Recheck the alignment of all parts, and recheck the tightness of all fasteners. 7. Set up the chair on a flat, level location. Do not exceed load capacity of 250 lbs. Maintenance 1. This chair is made of natural Fir wood. This beautiful material will naturally weather over time, especially if used outdoors.You can manage the speed and extent of this weathering by controlling the environment in which the chair is used and stored, as well as any coatings you may apply. 2. Leaving the chair outside exposed to weather, especially direct sun, rain and salt air, will speed the weathering process.This can be slowed by removing the chair from these conditions, or covering it with a suitable cover. 3. You may wish to stain, varnish or paint the chair. If so, follow the instructions supplied with these coatings. 4. Occasionally wash the chair with a garden hose or pressure sprayer to remove accumulated dust or dirt. Wipe down or blow off any remaining water left on the chair after washing. 5. Periodically (perhaps once per year), recheck the tightness of all fasteners. Normal usage of the chair and weathering of the wood may cause fasteners to loosen. SKU 91090-91091 Page 4 Assembly Drawings Assembly Drawings SKU 91090-91091 Page 5 Parts List Parts List Right Front Leg Back Support Left Arm Right Arm Front Support Wood Screws 55mm Bolt 65mm Bolt with Washer and Nut with Washer and Nut NOTE: Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts. PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MAN...
Otros modelos de este manual:Sillas - 91090 (184.51 kb)