Votos - 4, Puntuación media: 4
(
)
)
|
Resumen del manual
Contact Carrier/InvacareSolara jr.. Ventilator Tray Assembly, Installation and Operating InstructionsKit No. 1108526SAVE THESE INSTRUCTIONSNOTE: Check all parts for shipping damage. In case of damage, DO NOT use. Contact Carrier/InvacareSolara jr.. Ventilator Tray Assembly, Installation and Operating InstructionsKit No. 1108526 for further instructions. SAFETY SUMMAR. To ensure the safe and proper installation and use of the Ventilator Tray, these instruction. MUST be followed. GENERAL WARNING DO NOT install this equipment without first reading and understanding thi. instruction sheet and the Solara jr. Owner.s Manual, part number 1106628. I. you are unable to understand the warnings, cautions and instructions, contact . healthcare professional, dealer or technical personnel if applicable, befor. attempting to install this equipment - otherwise, injury or damage may occur. INSTALLATION WARNING After ANY adjustments, repair or service and BEFORE use, make sure that al. attaching hardware is tightened securely. NOTE: The ventilator tray kit can only be installed on 16-inch wide Solara jr. wheelchairs. If necessary. adjust the width of the wheelchair. Refer to the Solara jr. Service Manual, part number 1106629. This kit includes the following items. Descriptio. Quantit. Plug Butto. Washe. Locknu. Side Mounting Scre. Ventilator Tray with six (6) Strap. Rear Ventilator Tray Crossmembe. . . . . . . Part No. 110666. . Solara jr.. Ventilator Tra. INSTALLING THE VENTILATOR TRAY (FIGURE 1. 1. Remove and discard the two (2) SIDE mounting screws and washers securing the REA. crossmember to the base frame (DETAIL .A.). 2. Remove the REAR crossmember from the base frame (DETAIL .A.). 3. Remove and set aside the two (2) mounting screws and locknuts from the FRONT cross. member of the base frame (DETAIL .A.). 4. Remove and set aside the two (2) mounting screws and locknuts from the CENTE. crossmember of the base frame (DETAIL .A.). 5. Remove the plug buttons from the upper frame tubes of the base frame (DETAIL .A.). 6. Remove the two (2) mounting screws and locknuts securing the two (2) tilt slide housin. to the upper frame tubes (DETAIL .A.). 7. Remove and set aside the two (2) NEW side mounting screws, washers and locknuts fro. the rear of the ventilator tray. 8. Position the ventilator tray into the base frame as shown in DETAIL .B. of FIGURE 1. NOTE: Ensure the FRONT of the tray sits flush on the FRONT crossmember. NOTE: Ensure the CENTER fold of the tray sits flush on the CENTER crossmember. NOTE: Ensure the side mounting tabs are on the inside of the base frame. 9. Insert the rear ventilator tray crossmember into the ends of the upper frame tube. (DETAIL .A.). 10. Secure the rear ventilator tray crossmember and the tilt slide housing to the upper fram. tubes with the EXISTING mounting screws and locknuts removed in STEP 6 (DETAIL .A.). 11. Secure the FRONT of the ventilator tray to the front crossmember with the EXISTIN. two (2) mounting screws and locknuts removed in STEP 3 (DETAIL .B.). 12. Secure the CENTER fold of the ventilator tray to the CENTER crossmember with th. EXISTING two (2) mounting screws and locknuts removed in STEP 4 (DETAIL .B.). 13. Secure the side mounting tabs of the ventilator tray to the base frame with the two (2. NEW side mounting screws, washers and locknuts removed in STEP 7 (DETAIL .B.). NOTE: The side mounting tabs should be secured using the mounting hole below the rear upright. 14. Prepare the ventilator tray for use. Refer to USING THE VENTILATOR TRAY in thi. instruction sheet. Solara jr..Ventilator Tra. . Part No. 110666. Part No. 1106665 3 Solara jr.. Ventilator Tray FIGURE 1 - INSTALLING THE VENTILATOR TRAY Plug Buttons (STEP 5) Mounting Screw (STEPS 6 and 9) Locknut (STEP 6) REAR Ventilator Tray Crossmember (STEP 9) REAR Crossmember (STEP 2) Side Mounting Screw (STEP 1) Washer (STEP 1) CENTER Crossmember Mounting Screw (STEP 4) Locknut (STEP 3) FRONT Crossmember CENTER Crossmember Tilt Slide Housing (STEP 6) UPPER Frame Tube (STEP 8) FRONT Crossmember Mounting Screw (STEP 3) Locknut (STEP 4) DETAIL .B. DETAIL .A. Ventilator Tray (STEP 7) Washer (STEP 12) Locknut (STEP 12) FRONT Mounting Screws (STEP 10) FRONT Locknut (STEP 10) CENTER Locknut (STEP 11) CENTER Mounting Screw (STEP 11) CENTER Fold (STEP 7) FRONT of Ventilator Tray (STEP 10) REAR Upright Side Mounting Screw (STEP 1) Side Mounting Screw (STEP 12) Side Mounting Tab (STEPS 7 and 12) Invacare Corporation USA Canada One Invacare Way 570 Matheson Blvd. E Unit 8 Invacare is a registered trademark of Elyria, Ohio USA Mississauga Ontario Invacare Corporation. 44036-2125 L4Z4G4 Canada Yes, you can. and Solara jr. are 800-333-6900 800-668-5324 trademarks of Invacare Corporation. © 2001 Invacare Corporation Rev A 03/02 Part No. 1106665 USING THE VENTILATOR TRAY (FIGURE 2) NOTE: The ventilator tray straps are installed on the ventilator tray before the ventilator tray is shipped. 1. Position all six (6) strap slid...