Votos - 4, Puntuación media: 3.3
(
)
)
|
Resumen del manual
If you choose to use a screw lock, then the special bracket (located inside the meter case) must be used. DO NOT use the special bracket if a 1/4 turn lock is used. Coin Drawer Security — for additional security, drill out the two pilot holes on each front side of the meter case to 1/4 or 5/16 inch (6.4 or 8.0 mm) holes and install a bicycle lock through these holes. Timer Cams . (Metered Models) The dryer timer is factory equipped with a 45 minute timing cam. If this drying time is not suitable to your Electric Dryers 1-53242 Cams (30 Minutes) 1-53240 Cams (60 Minutes) installation, the following cams can be found in the envelope located in the cylinder: Gas Dryers 1-53242 Cams (30 Minutes) A 60 minute timing cam, Part No. 53240, is available for gas dryers as optional equipment at extra cost. 8 504523 Dryer Slide Extension A WARNING To reduce the risk of electric shock, fire, explosion, serious injury or death: • Disconnect electric power to the dryer(s) before servicing. • Close gas shut-off valve to gas dryer(s) before servicing. • Never start the dryer(s) with any guards/panels removed. • Whenever ground wires are removed during servicing, these ground wires must be reconnected to ensure that the dryer is properly grounded. 1. Assemble coin slide extension, No. 503733, to top side of coin slide using two Phillips head screws and lockwashers, No. 03950. Tighten firmly. 2. Install slide extension modifier, No. 501796, as follows: NOTE: Dryers equipped with Greenwald coin slides (except for Greenwald Comet Slide or Greenwald Tokette Slide) do not require the use of the slide extension modifier. • ESD Coin Slide - Mount slide extension modifier, No. 501796, to the underside of slide extension, No. 503733. Align the hole in the slide extension modifier with hole “A” in the slide extension and install self-tapping screw, No. 501086. Tighten firmly. • GREENWALD Comet Slide, GREENWALD Tokette Slide or MONARCH Coin Slide - Mount slide extension modifier, No. 501796, to the underside of slide extension, No. 503733. Align the hole in the slide extension modifier with hole “B” in the slide extension and install selftapping screw, No. 501086. Tighten firmly. 3. Reinstall coin slide in dryer meter case. 4. CHECK DRYER OPERATION - Connect electrical power to dryer. Place required number of coins in coin slide. Push slide in, and observe through service door opening in meter case. The slide extension should be contacting the accumulator actuator arm and moving back with slide travel. When slide is pushed all the way in, slide is retracted. Accumulator actuator arm should remain back until slide extension is moved forward and contacts actuator arm agian, returning arm to starting position. 5. After completing the dryer check, reinstall service door on top of meter case. NOTE: When reinstalling service door, front of door must be inserted at about a 45° angle in order to engage notched tabs with internal rib at top of meter case. 504523 9 Before You Start . . . Electrical • ELECTRIC DRYER Dryer needs a 3 wire and ground, 120/240 or 120/208 Volt, 30Amp., 60 Hertz, AC single Phase electrical supply. • GAS DRYER Dryer needs a 120 Volt, 15 Amp., 60 Hertz, polarized 3-slot effectively grounded receptacle. NOTE: For more detailed information, refer to Section on Electrical Requirements. Gas Dryer is equipped for Natural Gas with a 3/8"NPT gas supply connection. For more detailed information, refer to Section on Gas Requirements. Location Place the dryer on a solid floor with an adequate air supply. For more detailed information, refer to Section on Location Requirements. Exhaust Use rigid metal duct and exhaust the dryer to the outside by the shortest route possible. Tools For most installations, the basic tools you will need are: NOTE: For more detailed information, refer to Section on Dryer Exhaust Requirements. 10 504523 Installing the Dryer STEP 1: Position and Level the Dryer For further assistance refer to Section on Location Requirements. Install dryer before washer. This allows room for attaching exhaust duct. Install the four rubber cups found in the accessory bag. Place the dryer in position, and adjust the legs until the dryer is level. STEP 2: Connect Dryer Exhaust System For further assistance refer to Sections on Location Requirements and Dryer Exhaust Requirements. A WARNING A clothes dryer produces combustible lint. To reduce the risk of fire and combustion gas accumulation the dryer MUST be exhausted to the outdoors. DO NOT use plastic or thin foil flexible ducting. Locate dryer so exhaust duct is as short as possible. Be certain old ducts are cleaned before installing your new dryer. Use 10.2 cm (4") diameter rigid or flexible metal duct. Use as few elbows as possible. Use duct tape on all joints. Failure to exhaust dryer properly will void warranty. NOTE: Venting materials are not supplied with the dryer (obtain locally). IMPORTANT: DO...