Iniciar sesión:
Votos - 4, Puntuación media: 4.5 ( )

Manual de usuario Alliance Laundry Systems, modelo HDM3.5-1

Fabricar: Alliance Laundry Systems
Tamaño del archivo: 181.86 kb
Nombre del archivo: 5aef44fe-dffd-46ce-b0de-b1c551e6095f.pdf
Idioma del manual:en
Enlace gratuito para este manual disponible en la parte inferior de la página



Resumen del manual


Tools Required Drill & 3mm Bit 1 Philips Head Screw Driver 1 Wall Mounting Kit Includes Description 2 Hook 1 Plastic Spacers 2 Exhaust Duct 4 pieces 2. Fix the wall hanging brackets to the wall securely (eg. into the stud.) If the studs are too far apart fit a timber slat to the studs then mount the brackets onto the slat. The distance between each bracket is 155mm as per diagram. Wood Screws, 1 2g x 4 50mm Timber Screws Wall Hanging Brackets For Plaster/ Wooden Wall Ensure brackets aresecurely fastened. Fittimber slats if necessary Wall Mounting Instructions 3. To install the hook to the dryer, remove screws 1, 2, 3 & 4 as indicated in Fig. 2. 4. Align bracket as shown in Fig. 3 and refit screws tightly. 5. Remove lower side screws and install the spacers provided as per Fig. 2. 6. Install exhaust duct: for upwards discharge, joinsections 1 and 3, for downwards discharge, joinsections 1, 2, 2 & 3 as per Fig. 4. 7. With assistance, mount dryer on wall brackets. See Fig. 5. Maintenance Cleaning the Lint Filter Unplug the power cord prior to any cleaning. The lint filter must be cleaned before and after each use. Never use the dryer without the filter in place. 1. Removing the Filters Insert fingers into the four holes around the exhaust vent shroud and pull out to remove. The filter is in 3 parts: Exhaust vent shroud, lint filter and exhaust filter (as shown in figure 1). 2. Cleaning the filter Separate the filters from the shroud and remove the lint with a soft brush or vacuum cleaner. Take care not to damage the filters. (See fig 2). Cleaning of the Air Intake Filter The filter should be cleaned once a month. Hold the upper and lower edges of the air intake shroud, push upwards gently with your thumb to disconnect the latch hook then pull outwards to remove. Remove the filter from the shroud and clean it with a soft brush and refit. Cleaning the Interior & Exterior of the Dryer Do not use excessive water, just a damp cloth. Do not use solvents. Do not use spray cleaners when cleaning the interior. If the drum becomes stained, clean it with a damp cloth and allow to dry before using. Clean the cabinet with mild soap and water. Do not use harsh or abrasive cleaners. The lint filter is located at the back of the drum. Figure 1 3. Re-installing the Filter Reinstall in the reverse order, align the recess in the centre of the filters with the spigot in the centre of the drum and ensure that it is fitted firmly. (as shown in figure 3). Figure 3 Note: The filter fixed in the bottom of the drum should also be cleaned with a soft brush. Troubleshooting Review the following pages before calling for service. Problem Possible Cause What to do Timer knob does not turn. • Is the power on? • Insert the plug and turn on. Drum does not turn. • Is the door closed? • Is the power on? • Is there power to the wall socket? • Close the door. • Insert the plug and turn on. • Check another appliance in the wall socket. Exhaust air is not hot. • Is the timer incorrectly s...

Otros modelos de este manual:
Secadoras - HDM3.5-1 (181.86 kb)
Secadoras - HDM3.5-1 (181.86 kb)
Secadoras - HDM3.5-1 (181.86 kb)
Secadoras - HDM3.5-1 (181.86 kb)

Comentarios



Tu reseña
Tu nombre:
Introduzca dos números de la imagen:
capcha





Categoría