Iniciar sesión:
Votos - 3, Puntuación media: 3.7 ( )

Manual de usuario Alliance Laundry Systems, modelo DRY684C

Fabricar: Alliance Laundry Systems
Tamaño del archivo: 838.21 kb
Nombre del archivo: 513220.pdf
Idioma del manual:en
Enlace gratuito para este manual disponible en la parte inferior de la página



Resumen del manual


The dryer must not rock. DRY2234N 1 Dryer Base 2 Leveling Leg 3 Level 4 Rubber Cup 3 2 1 4 Installing the Dryer Step 1: Position and Level the Dryer Install dryer before washer. This allows room for attaching exhaust duct. Install the four rubber feet (in accessories bag). Select a location with a solid floor. Dryers installed in residential garages must be elevated 18 inches (46 cm) above the floor. Figure 2 IMPORTANT: In mobile home installations, gas dryers MUST be permanently attached to the floor at the time of installation. Order No. 526P3 Hold Down Kit (available at extra cost) for a manufactured (mobile) home installation. Follow the instructions supplied with the kit. Installation of unit must conform to the Manufactured Home Construction and Safety Standards, Title 24 CF4, Part 32-80 or Standard CAN/CSA-Z240 MH. 513220 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 7 Installation D817I * NOTE: For new installations, locate top of wall vent 42 inches (107 cm) above floor to make venting easier to connect. 1 Outer wall of enclosure B A A C *42" (107 cm) D A E 1 FRONT VIEW (w/o Closet Door) Area Description Free Standing/Alcove Installation A Dryer sides and rear clearance 0 in. (0 cm) B Dryer top clearance 12 in. (30.5 cm) C Dryer front clearance Not Applicable D Exhaust duct clearance to combustible material 2 in. (5.1 cm) E Weather hood to ground clearance 12 in. (30.5 cm) (Minimum clearances are shown.) SIDE VIEW Figure 3 8 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 513220 Installation Step 2: Connect Dryer Exhaust System WARNING To reduce the risk of fire and combustion gas accumulation the dryer MUST beexhausted to the outdoors. W604 To reduce the risk of fire and the accumulation of combustion gases, DO NOT exhaust dryer air into a window well, gas vent, chimney or enclosed, unventilated area, such as an attic, wall, ceiling, crawl space under a building or concealed space of a building. W045 WARNING This gas appliance contains or produces a chemical or chemicals which can cause death or serious illness and which are known to the State of California to cause cancer, birth defects, or other reproductive harm. To reduce the risk from substances in the fuel or from fuel combustion, make sure this appliance is installed, operated, and maintained according to the instructions in this manual. W115 To reduce the risk of fire, DO NOT use plastic or thin foil ducting to exhaust thedryer. W354 To reduce the risk of fire, the exhaust duct and weather hood MUST be fabricated of a material that will not support combustion. Rigid or flexible metal pipe is recommended for a clothes dryer. W048 WARNING To reduce the risk of fire due to increased static pressure, we do not recommendinstallation of in-line secondary lint filters or lint collectors. If secondary systems are mandated, frequently clean the system to assure safe operation. W749 IMPORTANT: Installing in-line filters or lint collectors will cause increased static pressure. Failure to maintain the secondary lint system will decrease dryer efficiency and may void machine warranty. • DO NOT use plastic or thin foil ducting. Rigid metal duct is recommended. Figure 4 D740I DO DON’T • Locate dryer so exhaust duct is as short as possible. • Be certain old ducts are cleaned before installing your new dryer. • Use 4 inch (10.2 cm) diameter rigid or flexible metal duct. • The male end of each section of duct must point away from the dryer. • Use as few elbows as possible. • Use duct tape or pop-rivets on all duct joints. DO NOT use sheet metal screws or fasteners on exhaust pipe joints which extend into the duct and catch lint. • Ductwork that runs through unheated areas must be insulated to help reduce condensation and lint build-up on pipe walls. • Install backdraft dampers in multi-dryer installations. • In mobile home installations, dryer exhaust duct must be secured to mobile home structure. • Dryer exhaust duct MUST NOT terminate under mobile home. • Dryer exhausts 220 cfm (measured at back of dryer). • DO NOT install flexible duct in concealed spaces, such as a wall or ceiling. 513220 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 9 Installation • Static pressure in exhaust duct should not be greater than .6 inches water column (1.5 cm), measured with manometer placed on exhaust duct two feet (61 cm) from dryer (check with dryer running and no load). In multi-dryer installations, all dryers connected to the main collector duct should be operating when pressure is checked. • Exhausting dryer in hard-to-reach locations can be done by installing 521P3 Flexible Metal Vent Kit (available as optional equipment at extra cost). • Sufficient make-up air must be supplied to replace the air exhausted by the dryer. The free area of any opening for outside air must be at least 40 in.2 (260 cm2). • Energy efficient buildings with low air infiltration rates should be equipped with an air exchanger that...


Comentarios



Tu reseña
Tu nombre:
Introduzca dos números de la imagen:
capcha





Categoría