Votos - 2, Puntuación media: 3.5
(
)
)
|
Resumen del manual
Mobile Home Installation Kit No. 346764 is available from your dealer. Refer to pages 2 and 3 for other important venting requirements. Installation MUST conform to current Manufactured Home Construction & Safety Standard (which is a Federal Regulation Title 24 CFR-Part 32-80) or when such standard is not applicable, with American National Standard for Mobile Homes. A CAUTION To prevent damage, do not use the control panel as a means to pick up or move the dryer. 2. Return the dryer to an upright position. REVERSING DOOR SWING Solid Door Reversing Instructions: 1. Open door and remove four (4) plugs in the door opening opposite the hinges. Retain all parts for uses later, unless otherwise noted. Note: Use care in removing plugs in not scratching paint on the front panel. Correct Incorrect UNPACKING 1. Using the four shipping carton corner posts (two on each side), carefully lay the dryer on its left side and remove the foam shipping base. REMOVE 4 SCREWS (ONE FROM EACH HINGE FIRST) 2. Begin removing the four (4) screws that attach the hinge to the front panel. For best results, start by only removing one screw per hinge. Then only loosen the two remaining screws while firmly holding door to prevent damage to hinge, front panel or door. After the remaining screws are loosened, continue to remove all. 3. Place door handle side down on a towel or pad to prevent any possible scratches to door. Remove all remaining four (4) screws between hinge and door. 4. Remove four (4) screws on opposite side of door. 5. Separate inner door from outer door by placing a flat screw driver or putty knife. Rotate the inner door 180 degree and reassemble the two door halves. 6. Install four (4) screws securing door halves where hinge was previously attached. 7. Install four (4) screws securing hinge to door assembly 8. Remove striker and discard. 9. Remove square plug and reinstall in hole striker was just removed. 10.Install striker (included in literature bag) into hole square plug was previously installed. 11. Grasping firmly the top of the door, position the door near the door opening and align the top hinge hole to the top hole in the front panel door opening. Once the first screw is started, attach the second screw to the lower hinge. Once both screws are tightened, install the remaining two screws. 12.Install four (4) plugs into the front panel door opening where hinges were originally installed. 1 2 3 4 5 6 7 Window Door Reversal Instructions Figure 1 I.Open door and remove four (4) plugs in the door opening opposite the hinges. Retain all parts for uses later, unless otherwise noted. (Figure 1) Note: Use care in removing plugs in not scratching paint on the front panel. Figure 2 2. Begin removing the four (4) screws that attach the hinge to the front panel. (Figure 2) For best results, start by only removing one screw per hinge. Then only loosen the two remaining screws while firmly holding door to prevent damage to hinge, front panel or door. After the remaining screws are loosened, continue to remove all. S- Figure 3 3. Place door on a towel or pad handle side down to prevent any possible scratches to door. Remove all remaining four (4) screws between hinge and door. (Figure 3) 4. Remove four (4) screws from side of door opposite of where hinge was mounted. Figure 4 5. Remove two (2) door handle screws and two (2) hole plugs from door. Again taking care not to scratch paint on door. (Figure 4) Figure 6 7. Separate the outer door from the inner door assembly with a putty knife or flat screw driver. (Figure 6) Figure 7 8. Remove lens locating screw. (Figure 7) Figure 8 9. Disengaging several of the retention tabs and pull lens away from the transition ring. (Figure 8) Figure 9 Figure 10 10. Remove two (2) transition ring plugs and reinstall on previous handle side. (Figures 9 and 10) 11. Reassemble lens to transition ring with holes to install handle on right-hand side of door assembly. For proper fit insure the retention tabs on transition ring are on top of lens \ Figure 11 12. Reassembly outer door to inner door assembly. (Figure 11) 13. Install four (4) screws securing hinge to door assembly in the new location, take note to place hinge in correct orientation. 14. Install four (4) screws into holes that had secured the hinge. 15. Remove striker and discard. 16. Remove square plug and reinstall in hole striker was just removed. 17. Install striker (included in literature bag) into hole square plug was previously installed. Figure 12 18. Reinstall door handle by placing the handle mounting bosses through holes in lens and transition ring and installing screws through inner door and tighten into handle bosses. (Figure 12). 19. Grasping firmly the top of the door, position the door near the door opening and align the top hinge hole to the top hole in the front panel door opening. Once the first screw is started, a ttach th e se co nd screw to t he l owe r hi n ...
Otros modelos de este manual:Secadoras - 0804 (6.22 mb)