Votos - 2, Puntuación media: 3.5
(
)
)
|
Resumen del manual
3. Press repeatedly OPTION button to select proper option. Selection is marked by rectangular border. 4. Press OK button to activate it. Suitable icon should appear on the right side of the screen. To deselect an option follow the same steps. Option icon should disappear. DELICATE For especially gentle drying of sensitive fabrics with the care label: and for temperature- sensitive textiles (e.g. acrylic, viscose). Programme is executed with reduced heat. DELICATE is only suitable for use with loads of up to 3kg. When the option is active, the DELICATE icon is on. SENSITIVE For gentle drying of fabrics that are frequently worn. Programme starts on full heat setting, which is then reduced as the programme progresses to be kind to the washing. When the option is active, the SENSITIVE icon is on. LONG ANTICREASE A 90 minute anti-crease phase is set. The display now shows the long anti-crease icon. If this additional option is selected, the anti-crease phase (30 min.) at the end of the drying cycle is lengthened by 60 minutes. The laundry can be removed at any time during the anti- crease phase. BUZZER The appliance is supplied with the BUZZER function deactivated. The button is used to switch the function on or off. When the function is active, the BUZZER symbol appears in the display. The buzzer sounds or plays a tune during: – cycle end – anti-crease phase and when phase starts or ends – cycle interruption by a warning –alarm CHILD LOCK The child lock can be set to prevent a programme being accidentally started or a programme in operation being accidentally changed. The child safety device locks all buttons and the programme knob. The child safety device can be deactivated by holding down the OPTION and OK buttons simultaneously for 5 seconds. 2) available with cotton/easy care and cotton/synthetic shirts programmes 24 24 Drying – Before programme is started: appliance cannot be used – After programme is started: programme in operation cannot be changed The child lock icon appears in the display to indicate that the child lock is activated. The child lock is not deactivated once the programme comes to an end. If you want to set a new programme, you must first deactivate the child lock. SPIN SPEED If the washing in the washing machine was initially drained prior to the drying cycle, the dryer can be set according to the spin speed of the initial drainage procedure. The higher the spin speed was, the shorter the programme length for the drying cycle. Activate the SPIN SPEED option and then number of times press OPTION button until the desired spin speed of the initial drainage is displayed. No value is shown if no spin speed is selected. In certain programmes the spin speed has (Highlight) no effect (time controlled cycles), its selection is not possible and only three dashes are visualised. Available selections: from 800 to 1800 rpm's in 100 rpm's intervals. The maximum value depends on the selected program, the minimum is always 800 rpm For those programs where the spin speed has no effect (time controlled cycles), the selection is not allowed and three dashes “- - -” are displayed that has the meaning of not set or unknown. The user interface always stores the last spin selection, and proposes it as default for all new selected programs. If memorised spin speed is greater than maximum allowed value it will be automatically reduced to max spin speed available for the selected program. Selecting TIME To select the programme duration after setting the TIME programme. You can select a programme duration from 10 minutes to 3 hours in 10-minute steps. 1. Turn the programme knob to the TIMED PROGRAMME. The 0:10 minutes is in the display (corresponding to the cooling phase). 2. Press the TIME button repeatedly until the desired programme duration is shown in the display, e.g. 0:20 for a programme of 20 minutes. If the programme duration is not selected, the duration is automatically set to 10 mins. Selecting DELAY START See chapter ProSteam system, section Selecting DELAY START. Starting the drying programme Press the START PAUSE button. The programme starts. The progress bar and the name of currently performed phase, above it, show stage of the cycle. With wet laundry, after a few minutes the appliance will show the correct programme duration and foreseen time of cycle end. It is normal for the appliance to make noises during drying programme if garments with hard parts, such as metal buttons, are put in the drum. Drying rack 25 Changing a programme To change a programme which has been selected by mistake once the programme has started, first turn the programme selector to OFF and then reset the programme. The programme can no longer be changed directly once the programme has started. If you nevertheless attempt to change the programme with the programme knob the following message is shown: Please turn programme selector to the last used position. The drying programme is not however affected by this. Putting in ext...
Otros modelos de este manual:Secadoras - 88840 (2.38 mb)
Secadoras - 88840 (2.38 mb)
Secadoras - 88840 (2.38 mb)